System Error Codes: 1 to 15841
System error codes will appear in software programs and in various areas within the Windows operating system after certain errors occur.1
Unfortunately,
sometimes all you get is the system error code but nothing about what
the code means! Once you know what the system error code means (below)
then you can work on fixing the problem.
1 - 1118 | 1119 - 1935 | 1936 - 8250 | 8251 - 12008 | 12009 - 15841 Error Code 1: Incorrect function. [ERROR_INVALID_FUNCTION (0x1)] Error Code 2: The system cannot find the file specified. [ERROR_FILE_NOT_FOUND (0x2)] Error Code 3: The system cannot find the path specified. [ERROR_PATH_NOT_FOUND (0x3)] Error Code 4: The system cannot open the file. [ERROR_TOO_MANY_OPEN_FILES (0x4)] Error Code 5: Access is denied. [ERROR_ACCESS_DENIED (0x5)] Error Code 6: The handle is invalid. [ERROR_INVALID_HANDLE (0x6)] Error Code 7: The storage control blocks were destroyed. [ERROR_ARENA_TRASHED (0x7)] Error Code 8: Not enough storage is available to process this command. [ERROR_NOT_ENOUGH_MEMORY (0x8)] Error Code 9: The storage control block address is invalid. [ERROR_INVALID_BLOCK (0x9)] Error Code 10: The environment is incorrect. [ERROR_BAD_ENVIRONMENT (0xA)] Error Code 11: An attempt was made to load a program with an incorrect format. [ERROR_BAD_FORMAT (0xB)] Error Code 12: The access code is invalid. [ERROR_INVALID_ACCESS (0xC)] Error Code 13: The data is invalid. [ERROR_INVALID_DATA (0xD)] Error Code 14: Not enough storage is available to complete this operation. [ERROR_OUTOFMEMORY (0xE)] Error Code 15: The system cannot find the drive specified. [ERROR_INVALID_DRIVE (0xF)] Error Code 16: The directory cannot be removed. [ERROR_CURRENT_DIRECTORY (0x10)] Error Code 17: The system cannot move the file to a different disk drive. [ERROR_NOT_SAME_DEVICE (0x11)] Error Code 18: There are no more files. [ERROR_NO_MORE_FILES (0x12)] Error Code 19: The media is write protected. [ERROR_WRITE_PROTECT (0x13)] Error Code 20: The system cannot find the device specified. [ERROR_BAD_UNIT (0x14)] Error Code 21: The device is not ready. [ERROR_NOT_READY (0x15)] Error Code 22: The device does not recognize the command. [ERROR_BAD_COMMAND (0x16)] Error Code 23: Data error (cyclic redundancy check). [ERROR_CRC (0x17)] Error Code 24: The program issued a command but the command length is incorrect. [ERROR_BAD_LENGTH (0x18)] Error Code 25: The drive cannot locate a specific area or track on the disk. [ERROR_SEEK (0x19)] Error Code 26: The specified disk or diskette cannot be accessed. [ERROR_NOT_DOS_DISK (0x1A)] Error Code 27: The drive cannot find the sector requested. [ERROR_SECTOR_NOT_FOUND (0x1B)] Error Code 28: The printer is out of paper. [ERROR_OUT_OF_PAPER (0x1C)] Error Code 29: The system cannot write to the specified device. [ERROR_WRITE_FAULT (0x1D)] Error Code 30: The system cannot read from the specified device. [ERROR_READ_FAULT (0x1E)] Error Code 31: A device attached to the system is not functioning. [ERROR_GEN_FAILURE (0x1F)] Error Code 32: The process cannot access the file because it is being used by another process. [ERROR_SHARING_VIOLATION (0x20)] Error Code 33: The process cannot access the file because another process has locked a portion of the file. [ERROR_LOCK_VIOLATION (0x21)] Error Code 34: The wrong diskette is in the drive. Insert %2 (Volume Serial Number: %3) into drive %1. [ERROR_WRONG_DISK (0x22)] Error Code 36: Too many files opened for sharing. [ERROR_SHARING_BUFFER_EXCEEDED (0x24)] Error Code 38: Reached the end of the file. [ERROR_HANDLE_EOF (0x26)] Error Code 39: The disk is full. [ERROR_HANDLE_DISK_FULL (0x27)] Error Code 50: The request is not supported. [ERROR_NOT_SUPPORTED (0x32)] Error Code 51:
Windows cannot find the network path. Verify that the network path is
correct and the destination computer is not busy or turned off. If
Windows still cannot find the network path contact your network
administrator. [ERROR_REM_NOT_LIST (0x33)] Error Code 52:
You were not connected because a duplicate name exists on the network.
If joining a domain, go to System in Control Panel to change the
computer name and try again. If joining a workgroup choose another
workgroup name. [ERROR_DUP_NAME (0x34)] Error Code 53: The network path was not found. [ERROR_BAD_NETPATH (0x35)] Error Code 54: The network is busy. [ERROR_NETWORK_BUSY (0x36)] Error Code 55: The specified network resource or device is no longer available. [ERROR_DEV_NOT_EXIST (0x37)] Error Code 56: The network BIOS command limit has been reached. [ERROR_TOO_MANY_CMDS (0x38)] Error Code 57: A network adapter hardware error occurred. [ERROR_ADAP_HDW_ERR (0x39)] Error Code 58: The specified server cannot perform the requested operation. [ERROR_BAD_NET_RESP (0x3A)] Error Code 59: An unexpected network error occurred. [ERROR_UNEXP_NET_ERR (0x3B)] Error Code 60: The remote adapter is not compatible. [ERROR_BAD_REM_ADAP (0x3C)] Error Code 61: The printer queue is full. [ERROR_PRINTQ_FULL (0x3D)] Error Code 62: Space to store the file waiting to be printed is not available on the server. [ERROR_NO_SPOOL_SPACE (0x3E)] Error Code 63: Your file waiting to be printed was deleted. [ERROR_PRINT_CANCELLED (0x3F)] Error Code 64: The specified network name is no longer available. [ERROR_NETNAME_DELETED (0x40)] Error Code 65: Network access is denied. [ERROR_NETWORK_ACCESS_DENIED (0x41)] Error Code 66: The network resource type is not correct. [ERROR_BAD_DEV_TYPE (0x42)] Error Code 67: The network name cannot be found. [ERROR_BAD_NET_NAME (0x43)] Error Code 68: The name limit for the local computer network adapter card was exceeded. [ERROR_TOO_MANY_NAMES (0x44)] Error Code 69: The network BIOS session limit was exceeded. [ERROR_TOO_MANY_SESS (0x45)] Error Code 70: The remote server has been paused or is in the process of being started. [ERROR_SHARING_PAUSED (0x46)] Error Code 71:
No more connections can be made to this remote computer at this time
because there are already as many connections as the computer can
accept. [ERROR_REQ_NOT_ACCEP (0x47)] Error Code 72: The specified printer or disk device has been paused. [ERROR_REDIR_PAUSED (0x48)] Error Code 80: The file exists. [ERROR_FILE_EXISTS (0x50)] Error Code 82: The directory or file cannot be created. [ERROR_CANNOT_MAKE (0x52)] Error Code 83: Fail on INT 24. [ERROR_FAIL_I24 (0x53)] Error Code 84: Storage to process this request is not available. [ERROR_OUT_OF_STRUCTURES (0x54)] Error Code 85: The local device name is already in use. [ERROR_ALREADY_ASSIGNED (0x55)] Error Code 86: The specified network password is not correct. [ERROR_INVALID_PASSWORD (0x56)] Error Code 87: The parameter is incorrect. [ERROR_INVALID_PARAMETER (0x57)] Error Code 88: A write fault occurred on the network. [ERROR_NET_WRITE_FAULT (0x58)] Error Code 89: The system cannot start another process at this time. [ERROR_NO_PROC_SLOTS (0x59)] Error Code 100: Cannot create another system semaphore. [ERROR_TOO_MANY_SEMAPHORES (0x64)] Error Code 101: The exclusive semaphore is owned by another process. [ERROR_EXCL_SEM_ALREADY_OWNED (0x65)] Error Code 102: The semaphore is set and cannot be closed. [ERROR_SEM_IS_SET (0x66)] Error Code 103: The semaphore cannot be set again. [ERROR_TOO_MANY_SEM_REQUESTS (0x67)] Error Code 104: Cannot request exclusive semaphores at interrupt time. [ERROR_INVALID_AT_INTERRUPT_TIME (0x68)] Error Code 105: The previous ownership of this semaphore has ended. [ERROR_SEM_OWNER_DIED (0x69)] Error Code 106: Insert the diskette for drive %1. [ERROR_SEM_USER_LIMIT (0x6A)] Error Code 107: The program stopped because an alternate diskette was not inserted. [ERROR_DISK_CHANGE (0x6B)] Error Code 108: The disk is in use or locked by another process. [ERROR_DRIVE_LOCKED (0x6C)] Error Code 109: The pipe has been ended. [ERROR_BROKEN_PIPE (0x6D)] Error Code 110: The system cannot open the device or file specified. [ERROR_OPEN_FAILED (0x6E)] Error Code 111: The file name is too long. [ERROR_BUFFER_OVERFLOW (0x6F)] Error Code 112: There is not enough space on the disk. [ERROR_DISK_FULL (0x70)] Error Code 113: No more internal file identifiers available. [ERROR_NO_MORE_SEARCH_HANDLES (0x71)] Error Code 114: The target internal file identifier is incorrect. [ERROR_INVALID_TARGET_HANDLE (0x72)] Error Code 117: The IOCTL call made by the application program is not correct. [ERROR_INVALID_CATEGORY (0x75)] Error Code 118: The verify-on-write switch parameter value is not correct. [ERROR_INVALID_VERIFY_SWITCH (0x76)] Error Code 119: The system does not support the command requested. [ERROR_BAD_DRIVER_LEVEL (0x77)] Error Code 120: This function is not supported on this system. [ERROR_CALL_NOT_IMPLEMENTED (0x78)] Error Code 121: The semaphore timeout period has expired. [ERROR_SEM_TIMEOUT (0x79)] Error Code 122: The data area passed to a system call is too small. [ERROR_INSUFFICIENT_BUFFER (0x7A)] Error Code 123: The filename, directory name or volume label syntax is incorrect. [ERROR_INVALID_NAME (0x7B)] Error Code 124: The system call level is not correct. [ERROR_INVALID_LEVEL (0x7C)] Error Code 125: The disk has no volume label. [ERROR_NO_VOLUME_LABEL (0x7D)] Error Code 126: The specified module could not be found. [ERROR_MOD_NOT_FOUND (0x7E)] Error Code 127: The specified procedure could not be found. [ERROR_PROC_NOT_FOUND (0x7F)] Error Code 128: There are no child processes to wait for. [ERROR_WAIT_NO_CHILDREN (0x80)] Error Code 129: The %1 application cannot be run in Win32 mode. [ERROR_CHILD_NOT_COMPLETE (0x81)] Error Code 130:
Attempt to use a file handle to an open disk partition for an operation
other than raw disk I/O. [ERROR_DIRECT_ACCESS_HANDLE (0x82)] Error Code 131: An attempt was made to move the file pointer before the beginning of the file. [ERROR_NEGATIVE_SEEK (0x83)] Error Code 132: The file pointer cannot be set on the specified device or file. [ERROR_SEEK_ON_DEVICE (0x84)] Error Code 133: A JOIN or SUBST command cannot be used for a drive that contains previously joined drives. [ERROR_IS_JOIN_TARGET (0x85)] Error Code 134: An attempt was made to use a JOIN or SUBST command on a drive that has already been joined. [ERROR_IS_JOINED (0x86)] Error Code 135: An attempt was made to use a JOIN or SUBST command on a drive that has already been substituted. [ERROR_IS_SUBSTED (0x87)] Error Code 136: The system tried to delete the JOIN of a drive that is not joined. [ERROR_NOT_JOINED (0x88)] Error Code 137: The system tried to delete the substitution of a drive that is not substituted. [ERROR_NOT_SUBSTED (0x89)] Error Code 138: The system tried to join a drive to a directory on a joined drive. [ERROR_JOIN_TO_JOIN (0x8A)] Error Code 139: The system tried to substitute a drive to a directory on a substituted drive. [ERROR_SUBST_TO_SUBST (0x8B)] Error Code 140: The system tried to join a drive to a directory on a substituted drive. [ERROR_JOIN_TO_SUBST (0x8C)] Error Code 141: The system tried to SUBST a drive to a directory on a joined drive. [ERROR_SUBST_TO_JOIN (0x8D)] Error Code 142: The system cannot perform a JOIN or SUBST at this time. [ERROR_BUSY_DRIVE (0x8E)] Error Code 143: The system cannot join or substitute a drive to or for a directory on the same drive. [ERROR_SAME_DRIVE (0x8F)] Error Code 144: The directory is not a subdirectory of the root directory. [ERROR_DIR_NOT_ROOT (0x90)] Error Code 145: The directory is not empty. [ERROR_DIR_NOT_EMPTY (0x91)] Error Code 146: The path specified is being used in a substitute. [ERROR_IS_SUBST_PATH (0x92)] Error Code 147: Not enough resources are available to process this command. [ERROR_IS_JOIN_PATH (0x93)] Error Code 148: The path specified cannot be used at this time. [ERROR_PATH_BUSY (0x94)] Error Code 149:
An attempt was made to join or substitute a drive for which a directory
on the drive is the target of a previous substitute.
[ERROR_IS_SUBST_TARGET (0x95)] Error Code 150: System trace information was not specified in your CONFIG.SYS file or tracing is disallowed. [ERROR_SYSTEM_TRACE (0x96)] Error Code 151: The number of specified semaphore events for DosMuxSemWait is not correct. [ERROR_INVALID_EVENT_COUNT (0x97)] Error Code 152: DosMuxSemWait did not execute too many semaphores are already set. [ERROR_TOO_MANY_MUXWAITERS (0x98)] Error Code 153: The DosMuxSemWait list is not correct. [ERROR_INVALID_LIST_FORMAT (0x99)] Error Code 154: The volume label you entered exceeds the label character limit of the target file system. [ERROR_LABEL_TOO_LONG (0x9A)] Error Code 155: Cannot create another thread. [ERROR_TOO_MANY_TCBS (0x9B)] Error Code 156: The recipient process has refused the signal. [ERROR_SIGNAL_REFUSED (0x9C)] Error Code 157: The segment is already discarded and cannot be locked. [ERROR_DISCARDED (0x9D)] Error Code 158: The segment is already unlocked. [ERROR_NOT_LOCKED (0x9E)] Error Code 159: The address for the thread ID is not correct. [ERROR_BAD_THREADID_ADDR (0x9F)] Error Code 160: One or more arguments are not correct. [ERROR_BAD_ARGUMENTS (0xA0)] Error Code 161: The specified path is invalid. [ERROR_BAD_PATHNAME (0xA1)] Error Code 162: A signal is already pending. [ERROR_SIGNAL_PENDING (0xA2)] Error Code 164: No more threads can be created in the system. [ERROR_MAX_THRDS_REACHED (0xA4)] Error Code 167: Unable to lock a region of a file. [ERROR_LOCK_FAILED (0xA7)] Error Code 170: The requested resource is in use. [ERROR_BUSY (0xAA)] Error Code 173: A lock request was not outstanding for the supplied cancel region. [ERROR_CANCEL_VIOLATION (0xAD)] Error Code 174: The file system does not support atomic changes to the lock type. [ERROR_ATOMIC_LOCKS_NOT_SUPPORTED (0xAE)] Error Code 180: The system detected a segment number that was not correct. [ERROR_INVALID_SEGMENT_NUMBER (0xB4)] Error Code 182: The operating system cannot run %1. [ERROR_INVALID_ORDINAL (0xB6)] Error Code 183: Cannot create a file when that file already exists. [ERROR_ALREADY_EXISTS (0xB7)] Error Code 186: The flag passed is not correct. [ERROR_INVALID_FLAG_NUMBER (0xBA)] Error Code 187: The specified system semaphore name was not found. [ERROR_SEM_NOT_FOUND (0xBB)] Error Code 188: The operating system cannot run %1. [ERROR_INVALID_STARTING_CODESEG (0xBC)] Error Code 189: The operating system cannot run %1. [ERROR_INVALID_STACKSEG (0xBD)] Error Code 190: The operating system cannot run %1. [ERROR_INVALID_MODULETYPE (0xBE)] Error Code 191: Cannot run %1 in Win32 mode. [ERROR_INVALID_EXE_SIGNATURE (0xBF)] Error Code 192: The operating system cannot run %1. [ERROR_EXE_MARKED_INVALID (0xC0)] Error Code 193: %1 is not a valid Win32 application. [ERROR_BAD_EXE_FORMAT (0xC1)] Error Code 194: The operating system cannot run %1. [ERROR_ITERATED_DATA_EXCEEDS_64k (0xC2)] Error Code 195: The operating system cannot run %1. [ERROR_INVALID_MINALLOCSIZE (0xC3)] Error Code 196: The operating system cannot run this application program. [ERROR_DYNLINK_FROM_INVALID_RING (0xC4)] Error Code 197: The operating system is not presently configured to run this application. [ERROR_IOPL_NOT_ENABLED (0xC5)] Error Code 198: The operating system cannot run %1. [ERROR_INVALID_SEGDPL (0xC6)] Error Code 199: The operating system cannot run this application program. [ERROR_AUTODATASEG_EXCEEDS_64k (0xC7)] Error Code 200: The code segment cannot be greater than or equal to 64K. [ERROR_RING2SEG_MUST_BE_MOVABLE (0xC8)] Error Code 201: The operating system cannot run %1. [ERROR_RELOC_CHAIN_XEEDS_SEGLIM (0xC9)] Error Code 202: The operating system cannot run %1. [ERROR_INFLOOP_IN_RELOC_CHAIN (0xCA)] Error Code 203: The system could not find the environment option that was entered. [ERROR_ENVVAR_NOT_FOUND (0xCB)] Error Code 205: No process in the command subtree has a signal handler. [ERROR_NO_SIGNAL_SENT (0xCD)] Error Code 206: The filename or extension is too long. [ERROR_FILENAME_EXCED_RANGE (0xCE)] Error Code 207: The ring 2 stack is in use. [ERROR_RING2_STACK_IN_USE (0xCF)] Error Code 208:
The global filename characters, * or ?, are entered incorrectly or too
many global filename characters are specified.
[ERROR_META_EXPANSION_TOO_LONG (0xD0)] Error Code 209: The signal being posted is not correct. [ERROR_INVALID_SIGNAL_NUMBER (0xD1)] Error Code 210: The signal handler cannot be set. [ERROR_THREAD_1_INACTIVE (0xD2)] Error Code 212: The segment is locked and cannot be reallocated. [ERROR_LOCKED (0xD4)] Error Code 214: Too many dynamic-link modules are attached to this program or dynamic-link module. [ERROR_TOO_MANY_MODULES (0xD6)] Error Code 215: Cannot nest calls to LoadModule. [ERROR_NESTING_NOT_ALLOWED (0xD7)] Error Code 216:
The version of %1 is not compatible with the version you're running.
Check your computer's system information to see whether you need a x86
(32-bit) or x64 (64-bit) version of the program, and then contact the
software publisher. [ERROR_EXE_MACHINE_TYPE_MISMATCH (0xD8)] Error Code 217: The image file %1 is signed, unable to modify. [ERROR_EXE_CANNOT_MODIFY_SIGNED_BINARY (0xD9)] Error Code 218: The image file %1 is strong signed, unable to modify. [ERROR_EXE_CANNOT_MODIFY_STRONG_SIGNED_BINARY (0xDA)] Error Code 220: This file is checked out or locked for editing by another user. [ERROR_FILE_CHECKED_OUT (0xDC)] Error Code 221: The file must be checked out before saving changes. [ERROR_CHECKOUT_REQUIRED (0xDD)] Error Code 222: The file type being saved or retrieved has been blocked. [ERROR_BAD_FILE_TYPE (0xDE)] Error Code 223: The file size exceeds the limit allowed and cannot be saved. [ERROR_FILE_TOO_LARGE (0xDF)] Error Code 224:
Access Denied. Before opening files in this location, you must first
add the web site to your trusted sites list, browse to the web site and
select the option to login automatically. [ERROR_FORMS_AUTH_REQUIRED
(0xE0)] Error Code 225: Operation did not complete successfully because the file contains a virus. [ERROR_VIRUS_INFECTED (0xE1)] Error Code 226:
This file contains a virus and cannot be opened. Due to the nature of
this virus, the file has been removed from this location.
[ERROR_VIRUS_DELETED (0xE2)] Error Code 229: The pipe is local. [ERROR_PIPE_LOCAL (0xE5)] Error Code 230: The pipe state is invalid. [ERROR_BAD_PIPE (0xE6)] Error Code 231: All pipe instances are busy. [ERROR_PIPE_BUSY (0xE7)] Error Code 232: The pipe is being closed. [ERROR_NO_DATA (0xE8)] Error Code 233: No process is on the other end of the pipe. [ERROR_PIPE_NOT_CONNECTED (0xE9)] Error Code 234: More data is available. [ERROR_MORE_DATA (0xEA)] Error Code 240: The session was canceled. [ERROR_VC_DISCONNECTED (0xF0)] Error Code 254: The specified extended attribute name was invalid. [ERROR_INVALID_EA_NAME (0xFE)] Error Code 255: The extended attributes are inconsistent. [ERROR_EA_LIST_INCONSISTENT (0xFF)] Error Code 258: The wait operation timed out. [WAIT_TIMEOUT (0x102)] Error Code 259: No more data is available. [ERROR_NO_MORE_ITEMS (0x103)] Error Code 266: The copy functions cannot be used. [ERROR_CANNOT_COPY (0x10A)] Error Code 267: The directory name is invalid. [ERROR_DIRECTORY (0x10B)] Error Code 275: The extended attributes did not fit in the buffer. [ERROR_EAS_DIDNT_FIT (0x113)] Error Code 276: The extended attribute file on the mounted file system is corrupt. [ERROR_EA_FILE_CORRUPT (0x114)] Error Code 277: The extended attribute table file is full. [ERROR_EA_TABLE_FULL (0x115)] Error Code 278: The specified extended attribute handle is invalid. [ERROR_INVALID_EA_HANDLE (0x116)] Error Code 282: The mounted file system does not support extended attributes. [ERROR_EAS_NOT_SUPPORTED (0x11A)] Error Code 288: Attempt to release mutex not owned by caller. [ERROR_NOT_OWNER (0x120)] Error Code 298: Too many posts were made to a semaphore. [ERROR_TOO_MANY_POSTS (0x12A)] Error Code 299: Only part of a ReadProcessMemory or WriteProcessMemory request was completed. [ERROR_PARTIAL_COPY (0x12B)] Error Code 300: The oplock request is denied. [ERROR_OPLOCK_NOT_GRANTED (0x12C)] Error Code 301: An invalid oplock acknowledgment was received by the system. [ERROR_INVALID_OPLOCK_PROTOCOL (0x12D)] Error Code 302: The volume is too fragmented to complete this operation. [ERROR_DISK_TOO_FRAGMENTED (0x12E)] Error Code 303: The file cannot be opened because it is in the process of being deleted. [ERROR_DELETE_PENDING (0x12F)] Error Code 317: The system cannot find message text for message number 0x%1 in the message file for %2. [ERROR_MR_MID_NOT_FOUND (0x13D)] Error Code 318: The scope specified was not found. [ERROR_SCOPE_NOT_FOUND (0x13E)] Error Code 350: No action was taken as a system reboot is required. [ERROR_FAIL_NOACTION_REBOOT (0x15E)] Error Code 351: The shutdown operation failed. [ERROR_FAIL_SHUTDOWN (0x15F)] Error Code 352: The restart operation failed. [ERROR_FAIL_RESTART (0x160)] Error Code 353: The maximum number of sessions has been reached. [ERROR_MAX_SESSIONS_REACHED (0x161)] Error Code 400: The thread is already in background processing mode. [ERROR_THREAD_MODE_ALREADY_BACKGROUND (0x190)] Error Code 401: The thread is not in background processing mode. [ERROR_THREAD_MODE_NOT_BACKGROUND (0x191)] Error Code 402: The process is already in background processing mode. [ERROR_PROCESS_MODE_ALREADY_BACKGROUND (0x192)] Error Code 403: The process is not in background processing mode. [ERROR_PROCESS_MODE_NOT_BACKGROUND (0x193)] Error Code 487: Attempt to access invalid address. [ERROR_INVALID_ADDRESS (0x1E7)] Error Code 500: User profile cannot be loaded. [ERROR_USER_PROFILE_LOAD (0x1F4)] Error Code 534: Arithmetic result exceeded 32 bits. [ERROR_ARITHMETIC_OVERFLOW (0x216)] Error Code 535: There is a process on other end of the pipe. [ERROR_PIPE_CONNECTED (0x217)] Error Code 536: Waiting for a process to open the other end of the pipe. [ERROR_PIPE_LISTENING (0x218)] Error Code 537: Application verifier has found an error in the current process. [ERROR_VERIFIER_STOP (0x219)] Error Code 538: An error occurred in the ABIOS subsystem. [ERROR_ABIOS_ERROR (0x21A)] Error Code 539: A warning occurred in the WX86 subsystem. [ERROR_WX86_WARNING (0x21B)] Error Code 540: An error occurred in the WX86 subsystem. [ERROR_WX86_ERROR (0x21C)] Error Code 541:
An attempt was made to cancel or set a timer that has an associated APC
and the subject thread is not the thread that originally set the timer
with an associated APC routine. [ERROR_TIMER_NOT_CANCELED (0x21D)] Error Code 542: Unwind exception code. [ERROR_UNWIND (0x21E)] Error Code 543: An invalid or unaligned stack was encountered during an unwind operation. [ERROR_BAD_STACK (0x21F)] Error Code 544: An invalid unwind target was encountered during an unwind operation. [ERROR_INVALID_UNWIND_TARGET (0x220)] Error Code 545:
Invalid Object Attributes specified to NtCreatePort or invalid Port
Attributes specified to NtConnectPort [ERROR_INVALID_PORT_ATTRIBUTES
(0x221)] Error Code 546: Length of
message passed to NtRequestPort or NtRequestWaitReplyPort was longer
than the maximum message allowed by the port.
[ERROR_PORT_MESSAGE_TOO_LONG (0x222)] Error Code 547: An attempt was made to lower a quota limit below the current usage. [ERROR_INVALID_QUOTA_LOWER (0x223)] Error Code 548: An attempt was made to attach to a device that was already attached to another device. [ERROR_DEVICE_ALREADY_ATTACHED (0x224)] Error Code 549:
An attempt was made to execute an instruction at an unaligned address
and the host system does not support unaligned instruction references.
[ERROR_INSTRUCTION_MISALIGNMENT (0x225)] Error Code 550: Profiling not started. [ERROR_PROFILING_NOT_STARTED (0x226)] Error Code 551: Profiling not stopped. [ERROR_PROFILING_NOT_STOPPED (0x227)] Error Code 552: The passed ACL did not contain the minimum required information. [ERROR_COULD_NOT_INTERPRET (0x228)] Error Code 553: The number of active profiling objects is at the maximum and no more may be started. [ERROR_PROFILING_AT_LIMIT (0x229)] Error Code 554: Used to indicate that an operation cannot continue without blocking for I/O. [ERROR_CANT_WAIT (0x22A)] Error Code 555:
Indicates that a thread attempted to terminate itself by default
(called NtTerminateThread with NULL) and it was the last thread in the
current process. [ERROR_CANT_TERMINATE_SELF (0x22B)] Error Code 556: If an MM error is returned which is not defined in the standard FsRtl filter [ERROR_UNEXPECTED_MM_CREATE_ERR (0x22C)] Error Code 557: If an MM error is returned which is not defined in the standard FsRtl filter [ERROR_UNEXPECTED_MM_MAP_ERROR (0x22D)] Error Code 558: If an MM error is returned which is not defined in the standard FsRtl filter [ERROR_UNEXPECTED_MM_EXTEND_ERR (0x22E)] Error Code 559: A malformed function table was encountered during an unwind operation. [ERROR_BAD_FUNCTION_TABLE (0x22F)] Error Code 560:
Indicates that an attempt was made to assign protection to a file
system file or directory and one of the SIDs in the security descriptor
could not be translated into a GUID that could be stored by the file
system. This causes the protection attempt to fail
[ERROR_NO_GUID_TRANSLATION (0x230)] Error Code 561: Indicates that an attempt was made to grow an LDT by setting its size [ERROR_INVALID_LDT_SIZE (0x231)] Error Code 563:
Indicates that the starting value for the LDT information was not an
integral multiple of the selector size. [ERROR_INVALID_LDT_OFFSET
(0x233)] Error Code 564: Indicates
that the user supplied an invalid descriptor when trying to set up Ldt
descriptors. [ERROR_INVALID_LDT_DESCRIPTOR (0x234)] Error Code 565: Indicates a process has too many threads to perform the requested action. For example [ERROR_TOO_MANY_THREADS (0x235)] Error Code 566: An attempt was made to operate on a thread within a specific process [ERROR_THREAD_NOT_IN_PROCESS (0x236)] Error Code 567: Page file quota was exceeded. [ERROR_PAGEFILE_QUOTA_EXCEEDED (0x237)] Error Code 568:
The Netlogon service cannot start because another Netlogon service
running in the domain conflicts with the specified role.
[ERROR_LOGON_SERVER_CONFLICT (0x238)] Error Code 569:
The SAM database on a Windows Server is significantly out of
synchronization with the copy on the Domain Controller. A complete
synchronization is required. [ERROR_SYNCHRONIZATION_REQUIRED (0x239)] Error Code 570: The NtCreateFile API failed. This error should never be returned to an application [ERROR_NET_OPEN_FAILED (0x23A)] Error Code 571: {Privilege Failed} The I/O permissions for the process could not be changed. [ERROR_IO_PRIVILEGE_FAILED (0x23B)] Error Code 572: {Application Exit by CTRL+C} The application terminated as a result of a CTRL+C. [ERROR_CONTROL_C_EXIT (0x23C)] Error Code 573: {Missing System File} The required system file %hs is bad or missing. [ERROR_MISSING_SYSTEMFILE (0x23D)] Error Code 574:
{Application Error} The exception %s (0x%08lx) occurred in the
application at location 0x%08lx. [ERROR_UNHANDLED_EXCEPTION (0x23E)] Error Code 575:
{Application Error} The application failed to initialize properly
(0x%lx). Click OK to terminate the application. [ERROR_APP_INIT_FAILURE
(0x23F)] Error Code 576: {Unable to
Create Paging File} The creation of the paging file %hs failed (%lx).
The requested size was %ld. [ERROR_PAGEFILE_CREATE_FAILED (0x240)] Error Code 577:
Windows cannot verify the digital signature for this file. A recent
hardware or software change might have installed a file that is signed
incorrectly or damaged [ERROR_INVALID_IMAGE_HASH (0x241)] Error Code 578: {No Paging File Specified} No paging file was specified in the system configuration. [ERROR_NO_PAGEFILE (0x242)] Error Code 579:
{EXCEPTION} A real-mode application issued a floating-point instruction
and floating-point hardware is not present.
[ERROR_ILLEGAL_FLOAT_CONTEXT (0x243)] Error Code 580:
An event pair synchronization operation was performed using the thread
specific client/server event pair object [ERROR_NO_EVENT_PAIR (0x244)] Error Code 581: A Windows Server has an incorrect configuration. [ERROR_DOMAIN_CTRLR_CONFIG_ERROR (0x245)] Error Code 582:
An illegal character was encountered. For a multi-byte character set
this includes a lead byte without a succeeding trail byte. For the
Unicode character set this includes the characters 0xFFFF and 0xFFFE.
[ERROR_ILLEGAL_CHARACTER (0x246)] Error Code 583: The Unicode character is not defined in the Unicode character set installed on the system. [ERROR_UNDEFINED_CHARACTER (0x247)] Error Code 584: The paging file cannot be created on a floppy diskette. [ERROR_FLOPPY_VOLUME (0x248)] Error Code 585:
The system BIOS failed to connect a system interrupt to the device or
bus for which the device is connected.
[ERROR_BIOS_FAILED_TO_CONNECT_INTERRUPT (0x249)] Error Code 586: This operation is only allowed for the Primary Domain Controller of the domain. [ERROR_BACKUP_CONTROLLER (0x24A)] Error Code 587:
An attempt was made to acquire a mutant such that its maximum count
would have been exceeded. [ERROR_MUTANT_LIMIT_EXCEEDED (0x24B)] Error Code 588:
A volume has been accessed for which a file system driver is required
that has not yet been loaded. [ERROR_FS_DRIVER_REQUIRED (0x24C)] Error Code 589:
{Registry File Failure} The registry cannot load the hive (file): %hs
or its log or alternate. It is corrupt [ERROR_CANNOT_LOAD_REGISTRY_FILE
(0x24D)] Error Code 590: {Unexpected
Failure in DebugActiveProcess} An unexpected failure occurred while
processing a DebugActiveProcess API request. You may choose OK to
terminate the process [ERROR_DEBUG_ATTACH_FAILED (0x24E)] Error Code 591:
{Fatal System Error} The %hs system process terminated unexpectedly
with a status of 0x%08x (0x%08x 0x%08x). The system has been shut down.
[ERROR_SYSTEM_PROCESS_TERMINATED (0x24F)] Error Code 592: {Data Not Accepted} The TDI client could not handle the data received during an indication. [ERROR_DATA_NOT_ACCEPTED (0x250)] Error Code 593: NTVDM encountered a hard error. [ERROR_VDM_HARD_ERROR (0x251)] Error Code 594:
{Cancel Timeout} The driver %hs failed to complete a canceled I/O
request in the allotted time. [ERROR_DRIVER_CANCEL_TIMEOUT (0x252)] Error Code 595: {Reply Message Mismatch} An attempt was made to reply to an LPC message [ERROR_REPLY_MESSAGE_MISMATCH (0x253)] Error Code 596:
{Delayed Write Failed} Windows was unable to save all the data for the
file %hs. The data has been lost. This error may be caused by a failure
of your computer hardware or network connection. Please try to save this
file elsewhere. [ERROR_LOST_WRITEBEHIND_DATA (0x254)] Error Code 597:
The parameter(s) passed to the server in the client/server shared
memory window were invalid. Too much data may have been put in the
shared memory window. [ERROR_CLIENT_SERVER_PARAMETERS_INVALID (0x255)] Error Code 598: The stream is not a tiny stream. [ERROR_NOT_TINY_STREAM (0x256)] Error Code 599: The request must be handled by the stack overflow code. [ERROR_STACK_OVERFLOW_READ (0x257)] Error Code 600:
Internal OFS status codes indicating how an allocation operation is
handled. Either it is retried after the containing onode is moved or the
extent stream is converted to a large stream. [ERROR_CONVERT_TO_LARGE
(0x258)] Error Code 601: The attempt
to find the object found an object matching by ID on the volume but it
is out of the scope of the handle used for the operation.
[ERROR_FOUND_OUT_OF_SCOPE (0x259)] Error Code 602: The bucket array must be grown. Retry transaction after doing so. [ERROR_ALLOCATE_BUCKET (0x25A)] Error Code 603: The user/kernel marshalling buffer has overflowed. [ERROR_MARSHALL_OVERFLOW (0x25B)] Error Code 604: The supplied variant structure contains invalid data. [ERROR_INVALID_VARIANT (0x25C)] Error Code 605: The specified buffer contains ill-formed data. [ERROR_BAD_COMPRESSION_BUFFER (0x25D)] Error Code 606: {Audit Failed} An attempt to generate a security audit failed. [ERROR_AUDIT_FAILED (0x25E)] Error Code 607: The timer resolution was not previously set by the current process. [ERROR_TIMER_RESOLUTION_NOT_SET (0x25F)] Error Code 608: There is insufficient account information to log you on. [ERROR_INSUFFICIENT_LOGON_INFO (0x260)] Error Code 609:
{Invalid DLL Entrypoint} The dynamic link library %hs is not written
correctly. The stack pointer has been left in an inconsistent state. The
entrypoint should be declared as WINAPI or STDCALL. Select YES to fail
the DLL load. Select NO to continue execution. Selecting NO may cause
the application to operate incorrectly. [ERROR_BAD_DLL_ENTRYPOINT
(0x261)] Error Code 610: {Invalid
Service Callback Entrypoint} The %hs service is not written correctly.
The stack pointer has been left in an inconsistent state. The callback
entrypoint should be declared as WINAPI or STDCALL. Selecting OK will
cause the service to continue operation. However
[ERROR_BAD_SERVICE_ENTRYPOINT (0x262)] Error Code 611: There is an IP address conflict with another system on the network [ERROR_IP_ADDRESS_CONFLICT1 (0x263)] Error Code 612: There is an IP address conflict with another system on the network [ERROR_IP_ADDRESS_CONFLICT2 (0x264)] Error Code 613:
{Low On Registry Space} The system has reached the maximum size allowed
for the system part of the registry. Additional storage requests will
be ignored. [ERROR_REGISTRY_QUOTA_LIMIT (0x265)] Error Code 614: A callback return system service cannot be executed when no callback is active. [ERROR_NO_CALLBACK_ACTIVE (0x266)] Error Code 615:
The password provided is too short to meet the policy of your user
account. Please choose a longer password. [ERROR_PWD_TOO_SHORT (0x267)] Error Code 616:
The policy of your user account does not allow you to change passwords
too frequently. This is done to prevent users from changing back to a
familiar [ERROR_PWD_TOO_RECENT (0x268)] Error Code 617:
You have attempted to change your password to one that you have used in
the past. The policy of your user account does not allow this. Please
select a password that you have not previously used.
[ERROR_PWD_HISTORY_CONFLICT (0x269)] Error Code 618: The specified compression format is unsupported. [ERROR_UNSUPPORTED_COMPRESSION (0x26A)] Error Code 619: The specified hardware profile configuration is invalid. [ERROR_INVALID_HW_PROFILE (0x26B)] Error Code 620: The specified Plug and Play registry device path is invalid. [ERROR_INVALID_PLUGPLAY_DEVICE_PATH (0x26C)] Error Code 621: The specified quota list is internally inconsistent with its descriptor. [ERROR_QUOTA_LIST_INCONSISTENT (0x26D)] Error Code 622:
{Windows Evaluation Notification} The evaluation period for this
installation of Windows has expired. This system will shutdown in 1
hour. To restore access to this installation of Windows
[ERROR_EVALUATION_EXPIRATION (0x26E)] Error Code 623:
{Illegal System DLL Relocation} The system DLL %hs was relocated in
memory. The application will not run properly. The relocation occurred
because the DLL %hs occupied an address range reserved for Windows
system DLLs. The vendor supplying the DLL should be contacted for a new
DLL. [ERROR_ILLEGAL_DLL_RELOCATION (0x26F)] Error Code 624:
{DLL Initialization Failed} The application failed to initialize
because the window station is shutting down.
[ERROR_DLL_INIT_FAILED_LOGOFF (0x270)] Error Code 625: The validation process needs to continue on to the next step. [ERROR_VALIDATE_CONTINUE (0x271)] Error Code 626: There are no more matches for the current index enumeration. [ERROR_NO_MORE_MATCHES (0x272)] Error Code 627: The range could not be added to the range list because of a conflict. [ERROR_RANGE_LIST_CONFLICT (0x273)] Error Code 628: The server process is running under a SID different than that required by client. [ERROR_SERVER_SID_MISMATCH (0x274)] Error Code 629: A group marked use for deny only cannot be enabled. [ERROR_CANT_ENABLE_DENY_ONLY (0x275)] Error Code 630: {EXCEPTION} Multiple floating point faults. [ERROR_FLOAT_MULTIPLE_FAULTS (0x276)] Error Code 631: {EXCEPTION} Multiple floating point traps. [ERROR_FLOAT_MULTIPLE_TRAPS (0x277)] Error Code 632: The requested interface is not supported. [ERROR_NOINTERFACE (0x278)] Error Code 633:
{System Standby Failed} The driver %hs does not support standby mode.
Updating this driver may allow the system to go to standby mode.
[ERROR_DRIVER_FAILED_SLEEP (0x279)] Error Code 634: The system file %1 has become corrupt and has been replaced. [ERROR_CORRUPT_SYSTEM_FILE (0x27A)] Error Code 635:
{Virtual Memory Minimum Too Low} Your system is low on virtual memory.
Windows is increasing the size of your virtual memory paging file.
During this process [ERROR_COMMITMENT_MINIMUM (0x27B)] Error Code 636: A device was removed so enumeration must be restarted. [ERROR_PNP_RESTART_ENUMERATION (0x27C)] Error Code 637:
{Fatal System Error} The system image %s is not properly signed. The
file has been replaced with the signed file. The system has been shut
down. [ERROR_SYSTEM_IMAGE_BAD_SIGNATURE (0x27D)] Error Code 638: Device will not start without a reboot. [ERROR_PNP_REBOOT_REQUIRED (0x27E)] Error Code 639: There is not enough power to complete the requested operation. [ERROR_INSUFFICIENT_POWER (0x27F)] Error Code 640: ERROR_MULTIPLE_FAULT_VIOLATION [ERROR_MULTIPLE_FAULT_VIOLATION (0x280)] Error Code 641: The system is in the process of shutting down. [ERROR_SYSTEM_SHUTDOWN (0x281)] Error Code 642: An attempt to remove a processes DebugPort was made [ERROR_PORT_NOT_SET (0x282)] Error Code 643:
This version of Windows is not compatible with the behavior version of
directory forest [ERROR_DS_VERSION_CHECK_FAILURE (0x283)] Error Code 644: The specified range could not be found in the range list. [ERROR_RANGE_NOT_FOUND (0x284)] Error Code 646: The driver was not loaded because the system is booting into safe mode. [ERROR_NOT_SAFE_MODE_DRIVER (0x286)] Error Code 647: The driver was not loaded because it failed it's initialization call. [ERROR_FAILED_DRIVER_ENTRY (0x287)] Error Code 648:
The "%hs" encountered an error while applying power or reading the
device configuration. This may be caused by a failure of your hardware
or by a poor connection. [ERROR_DEVICE_ENUMERATION_ERROR (0x288)] Error Code 649:
The create operation failed because the name contained at least one
mount point which resolves to a volume to which the specified device
object is not attached. [ERROR_MOUNT_POINT_NOT_RESOLVED (0x289)] Error Code 650:
The device object parameter is either not a valid device object or is
not attached to the volume specified by the file name.
[ERROR_INVALID_DEVICE_OBJECT_PARAMETER (0x28A)] Error Code 651: A Machine Check Error has occurred. Please check the system eventlog for additional information. [ERROR_MCA_OCCURED (0x28B)] Error Code 652: There was error [%2] processing the driver database. [ERROR_DRIVER_DATABASE_ERROR (0x28C)] Error Code 653: System hive size has exceeded its limit. [ERROR_SYSTEM_HIVE_TOO_LARGE (0x28D)] Error Code 654:
The driver could not be loaded because a previous version of the driver
is still in memory. [ERROR_DRIVER_FAILED_PRIOR_UNLOAD (0x28E)] Error Code 655:
{Volume Shadow Copy Service} Please wait while the Volume Shadow Copy
Service prepares volume %hs for hibernation.
[ERROR_VOLSNAP_PREPARE_HIBERNATE (0x28F)] Error Code 656:
The system has failed to hibernate (The error code is %hs). Hibernation
will be disabled until the system is restarted.
[ERROR_HIBERNATION_FAILURE (0x290)] Error Code 665: The requested operation could not be completed due to a file system limitation [ERROR_FILE_SYSTEM_LIMITATION (0x299)] Error Code 668: An assertion failure has occurred. [ERROR_ASSERTION_FAILURE (0x29C)] Error Code 669: An error occurred in the ACPI subsystem. [ERROR_ACPI_ERROR (0x29D)] Error Code 670: WOW Assertion Error. [ERROR_WOW_ASSERTION (0x29E)] Error Code 671:
A device is missing in the system BIOS MPS table. This device will not
be used. Please contact your system vendor for system BIOS update.
[ERROR_PNP_BAD_MPS_TABLE (0x29F)] Error Code 672: A translator failed to translate resources. [ERROR_PNP_TRANSLATION_FAILED (0x2A0)] Error Code 673: A IRQ translator failed to translate resources. [ERROR_PNP_IRQ_TRANSLATION_FAILED (0x2A1)] Error Code 674: Driver %2 returned invalid ID for a child device (%3). [ERROR_PNP_INVALID_ID (0x2A2)] Error Code 675: {Kernel Debugger Awakened} the system debugger was awakened by an interrupt. [ERROR_WAKE_SYSTEM_DEBUGGER (0x2A3)] Error Code 676:
{Handles Closed} Handles to objects have been automatically closed as a
result of the requested operation. [ERROR_HANDLES_CLOSED (0x2A4)] Error Code 677:
{Too Much Information} The specified access control list (ACL)
contained more information than was expected.
[ERROR_EXTRANEOUS_INFORMATION (0x2A5)] Error Code 678:
This warning level status indicates that the transaction state already
exists for the registry sub-tree [ERROR_RXACT_COMMIT_NECESSARY (0x2A6)] Error Code 679: {Media Changed} The media may have changed. [ERROR_MEDIA_CHECK (0x2A7)] Error Code 680:
{GUID Substitution} During the translation of a global identifier
(GUID) to a Windows security ID (SID) [ERROR_GUID_SUBSTITUTION_MADE
(0x2A8)] Error Code 681: The create operation stopped after reaching a symbolic link [ERROR_STOPPED_ON_SYMLINK (0x2A9)] Error Code 682: A long jump has been executed. [ERROR_LONGJUMP (0x2AA)] Error Code 683: The Plug and Play query operation was not successful. [ERROR_PLUGPLAY_QUERY_VETOED (0x2AB)] Error Code 684: A frame consolidation has been executed. [ERROR_UNWIND_CONSOLIDATE (0x2AC)] Error Code 685:
{Registry Hive Recovered} Registry hive (file): %hs was corrupted and
it has been recovered. Some data might have been lost.
[ERROR_REGISTRY_HIVE_RECOVERED (0x2AD)] Error Code 686:
The application is attempting to run executable code from the module
%hs. This may be insecure. An alternative [ERROR_DLL_MIGHT_BE_INSECURE
(0x2AE)] Error Code 687: The application is loading executable code from the module %hs. This is secure [ERROR_DLL_MIGHT_BE_INCOMPATIBLE (0x2AF)] Error Code 688: Debugger did not handle the exception. [ERROR_DBG_EXCEPTION_NOT_HANDLED (0x2B0)] Error Code 689: Debugger will reply later. [ERROR_DBG_REPLY_LATER (0x2B1)] Error Code 690: Debugger cannot provide handle. [ERROR_DBG_UNABLE_TO_PROVIDE_HANDLE (0x2B2)] Error Code 691: Debugger terminated thread. [ERROR_DBG_TERMINATE_THREAD (0x2B3)] Error Code 692: Debugger terminated process. [ERROR_DBG_TERMINATE_PROCESS (0x2B4)] Error Code 693: Debugger got control C. [ERROR_DBG_CONTROL_C (0x2B5)] Error Code 694: Debugger printed exception on control C. [ERROR_DBG_PRINTEXCEPTION_C (0x2B6)] Error Code 695: Debugger received RIP exception. [ERROR_DBG_RIPEXCEPTION (0x2B7)] Error Code 696: Debugger received control break. [ERROR_DBG_CONTROL_BREAK (0x2B8)] Error Code 697: Debugger command communication exception. [ERROR_DBG_COMMAND_EXCEPTION (0x2B9)] Error Code 698: {Object Exists} An attempt was made to create an object and the object name already existed. [ERROR_OBJECT_NAME_EXISTS (0x2BA)] Error Code 699:
{Thread Suspended} A thread termination occurred while the thread was
suspended. The thread was resumed [ERROR_THREAD_WAS_SUSPENDED (0x2BB)] Error Code 700:
{Image Relocated} An image file could not be mapped at the address
specified in the image file. Local fixups must be performed on this
image. [ERROR_IMAGE_NOT_AT_BASE (0x2BC)] Error Code 701:
This informational level status indicates that a specified registry
sub-tree transaction state did not yet exist and had to be created.
[ERROR_RXACT_STATE_CREATED (0x2BD)] Error Code 702: {Segment Load} A virtual DOS machine (VDM) is loading [ERROR_SEGMENT_NOTIFICATION (0x2BE)] Error Code 703:
{Invalid Current Directory} The process cannot switch to the startup
current directory %hs. Select OK to set current directory to %hs
[ERROR_BAD_CURRENT_DIRECTORY (0x2BF)] Error Code 704: {Redundant Read} To satisfy a read request [ERROR_FT_READ_RECOVERY_FROM_BACKUP (0x2C0)] Error Code 705: {Redundant Write} To satisfy a write request [ERROR_FT_WRITE_RECOVERY (0x2C1)] Error Code 706: {Machine Type Mismatch} The image file %hs is valid [ERROR_IMAGE_MACHINE_TYPE_MISMATCH (0x2C2)] Error Code 707:
{Partial Data Received} The network transport returned partial data to
its client. The remaining data will be sent later.
[ERROR_RECEIVE_PARTIAL (0x2C3)] Error Code 708:
{Expedited Data Received} The network transport returned data to its
client that was marked as expedited by the remote system.
[ERROR_RECEIVE_EXPEDITED (0x2C4)] Error Code 709:
{Partial Expedited Data Received} The network transport returned
partial data to its client and this data was marked as expedited by the
remote system. The remaining data will be sent later.
[ERROR_RECEIVE_PARTIAL_EXPEDITED (0x2C5)] Error Code 710: {TDI Event Done} The TDI indication has completed successfully. [ERROR_EVENT_DONE (0x2C6)] Error Code 711: {TDI Event Pending} The TDI indication has entered the pending state. [ERROR_EVENT_PENDING (0x2C7)] Error Code 712: Checking file system on %wZ [ERROR_CHECKING_FILE_SYSTEM (0x2C8)] Error Code 713: {Fatal Application Exit} %hs [ERROR_FATAL_APP_EXIT (0x2C9)] Error Code 714: The specified registry key is referenced by a predefined handle. [ERROR_PREDEFINED_HANDLE (0x2CA)] Error Code 715:
{Page Unlocked} The page protection of a locked page was changed to 'No
Access' and the page was unlocked from memory and from the process.
[ERROR_WAS_UNLOCKED (0x2CB)] Error Code 716: %hs [ERROR_SERVICE_NOTIFICATION (0x2CC)] Error Code 717: {Page Locked} One of the pages to lock was already locked. [ERROR_WAS_LOCKED (0x2CD)] Error Code 718: Application popup: %1 : %2 [ERROR_LOG_HARD_ERROR (0x2CE)] Error Code 719: ERROR_ALREADY_WIN32 [ERROR_ALREADY_WIN32 (0x2CF)] Error Code 720: {Machine Type Mismatch} The image file %hs is valid [ERROR_IMAGE_MACHINE_TYPE_MISMATCH_EXE (0x2D0)] Error Code 721: A yield execution was performed and no thread was available to run. [ERROR_NO_YIELD_PERFORMED (0x2D1)] Error Code 722: The resumable flag to a timer API was ignored. [ERROR_TIMER_RESUME_IGNORED (0x2D2)] Error Code 723: The arbiter has deferred arbitration of these resources to its parent [ERROR_ARBITRATION_UNHANDLED (0x2D3)] Error Code 724: The inserted CardBus device cannot be started because of a configuration error on "%hs". [ERROR_CARDBUS_NOT_SUPPORTED (0x2D4)] Error Code 725:
The CPUs in this multiprocessor system are not all the same revision
level. To use all processors the operating system restricts itself to
the features of the least capable processor in the system. Should
problems occur with this system [ERROR_MP_PROCESSOR_MISMATCH (0x2D5)] Error Code 726: The system was put into hibernation. [ERROR_HIBERNATED (0x2D6)] Error Code 727: The system was resumed from hibernation. [ERROR_RESUME_HIBERNATION (0x2D7)] Error Code 728: Windows has detected that the system firmware (BIOS) was updated [previous firmware date = %2 [ERROR_FIRMWARE_UPDATED (0x2D8)] Error Code 729:
A device driver is leaking locked I/O pages causing system degradation.
The system has automatically enabled tracking code in order to try and
catch the culprit. [ERROR_DRIVERS_LEAKING_LOCKED_PAGES (0x2D9)] Error Code 730: The system has awoken [ERROR_WAKE_SYSTEM (0x2DA)] Error Code 731: ERROR_WAIT_1 [ERROR_WAIT_1 (0x2DB)] Error Code 732: ERROR_WAIT_2 [ERROR_WAIT_2 (0x2DC)] Error Code 733: ERROR_WAIT_3 [ERROR_WAIT_3 (0x2DD)] Error Code 734: ERROR_WAIT_63 [ERROR_WAIT_63 (0x2DE)] Error Code 735: ERROR_ABANDONED_WAIT_0 [ERROR_ABANDONED_WAIT_0 (0x2DF)] Error Code 736: ERROR_ABANDONED_WAIT_63 [ERROR_ABANDONED_WAIT_63 (0x2E0)] Error Code 737: ERROR_USER_APC [ERROR_USER_APC (0x2E1)] Error Code 738: ERROR_KERNEL_APC [ERROR_KERNEL_APC (0x2E2)] Error Code 739: ERROR_ALERTED [ERROR_ALERTED (0x2E3)] Error Code 740: The requested operation requires elevation. [ERROR_ELEVATION_REQUIRED (0x2E4)] Error Code 741:
A reparse should be performed by the Object Manager since the name of
the file resulted in a symbolic link. [ERROR_REPARSE (0x2E5)] Error Code 742: An open/create operation completed while an oplock break is underway. [ERROR_OPLOCK_BREAK_IN_PROGRESS (0x2E6)] Error Code 743: A new volume has been mounted by a file system. [ERROR_VOLUME_MOUNTED (0x2E7)] Error Code 744:
This success level status indicates that the transaction state already
exists for the registry sub-tree [ERROR_RXACT_COMMITTED (0x2E8)] Error Code 745:
This indicates that a notify change request has been completed due to
closing the handle which made the notify change request.
[ERROR_NOTIFY_CLEANUP (0x2E9)] Error Code 746:
{Connect Failure on Primary Transport} An attempt was made to connect
to the remote server %hs on the primary transport
[ERROR_PRIMARY_TRANSPORT_CONNECT_FAILED (0x2EA)] Error Code 747: Page fault was a transition fault. [ERROR_PAGE_FAULT_TRANSITION (0x2EB)] Error Code 748: Page fault was a demand zero fault. [ERROR_PAGE_FAULT_DEMAND_ZERO (0x2EC)] Error Code 749: Page fault was a demand zero fault. [ERROR_PAGE_FAULT_COPY_ON_WRITE (0x2ED)] Error Code 750: Page fault was a demand zero fault. [ERROR_PAGE_FAULT_GUARD_PAGE (0x2EE)] Error Code 751: Page fault was satisfied by reading from a secondary storage device. [ERROR_PAGE_FAULT_PAGING_FILE (0x2EF)] Error Code 752: Cached page was locked during operation. [ERROR_CACHE_PAGE_LOCKED (0x2F0)] Error Code 753: Crash dump exists in paging file. [ERROR_CRASH_DUMP (0x2F1)] Error Code 754: Specified buffer contains all zeros. [ERROR_BUFFER_ALL_ZEROS (0x2F2)] Error Code 755:
A reparse should be performed by the Object Manager since the name of
the file resulted in a symbolic link. [ERROR_REPARSE_OBJECT (0x2F3)] Error Code 756: The device has succeeded a query-stop and its resource requirements have changed. [ERROR_RESOURCE_REQUIREMENTS_CHANGED (0x2F4)] Error Code 757:
The translator has translated these resources into the global space and
no further translations should be performed.
[ERROR_TRANSLATION_COMPLETE (0x2F5)] Error Code 758: A process being terminated has no threads to terminate. [ERROR_NOTHING_TO_TERMINATE (0x2F6)] Error Code 759: The specified process is not part of a job. [ERROR_PROCESS_NOT_IN_JOB (0x2F7)] Error Code 760: The specified process is part of a job. [ERROR_PROCESS_IN_JOB (0x2F8)] Error Code 761: {Volume Shadow Copy Service} The system is now ready for hibernation. [ERROR_VOLSNAP_HIBERNATE_READY (0x2F9)] Error Code 762:
A file system or file system filter driver has successfully completed
an FsFilter operation. [ERROR_FSFILTER_OP_COMPLETED_SUCCESSFULLY
(0x2FA)] Error Code 763: The specified interrupt vector was already connected. [ERROR_INTERRUPT_VECTOR_ALREADY_CONNECTED (0x2FB)] Error Code 764: The specified interrupt vector is still connected. [ERROR_INTERRUPT_STILL_CONNECTED (0x2FC)] Error Code 765: An operation is blocked waiting for an oplock. [ERROR_WAIT_FOR_OPLOCK (0x2FD)] Error Code 766: Debugger handled exception [ERROR_DBG_EXCEPTION_HANDLED (0x2FE)] Error Code 767: Debugger continued [ERROR_DBG_CONTINUE (0x2FF)] Error Code 768:
An exception occurred in a user mode callback and the kernel callback
frame should be removed. [ERROR_CALLBACK_POP_STACK (0x300)] Error Code 769: Compression is disabled for this volume. [ERROR_COMPRESSION_DISABLED (0x301)] Error Code 770: The data provider cannot fetch backwards through a result set. [ERROR_CANTFETCHBACKWARDS (0x302)] Error Code 771: The data provider cannot scroll backwards through a result set. [ERROR_CANTSCROLLBACKWARDS (0x303)] Error Code 772:
The data provider requires that previously fetched data is released
before asking for more data. [ERROR_ROWSNOTRELEASED (0x304)] Error Code 773:
The data provider was not able to interpret the flags set for a column
binding in an accessor. [ERROR_BAD_ACCESSOR_FLAGS (0x305)] Error Code 774: One or more errors occurred while processing the request. [ERROR_ERRORS_ENCOUNTERED (0x306)] Error Code 775: The implementation is not capable of performing the request. [ERROR_NOT_CAPABLE (0x307)] Error Code 776:
The client of a component requested an operation which is not valid
given the state of the component instance.
[ERROR_REQUEST_OUT_OF_SEQUENCE (0x308)] Error Code 777: A version number could not be parsed. [ERROR_VERSION_PARSE_ERROR (0x309)] Error Code 778: The iterator's start position is invalid. [ERROR_BADSTARTPOSITION (0x30A)] Error Code 779: The hardware has reported an uncorrectable memory error. [ERROR_MEMORY_HARDWARE (0x30B)] Error Code 780: The attempted operation required self healing to be enabled. [ERROR_DISK_REPAIR_DISABLED (0x30C)] Error Code 781:
The Desktop heap encountered an error while allocating session memory.
There is more information in the system event log.
[ERROR_INSUFFICIENT_RESOURCE_FOR_SPECIFIED_SHARED_SECTION_SIZE (0x30D)] Error Code 782: The system power state is transitioning from %2 to %3. [ERROR_SYSTEM_POWERSTATE_TRANSITION (0x30E)] Error Code 783: The system power state is transitioning from %2 to %3 but could enter %4. [ERROR_SYSTEM_POWERSTATE_COMPLEX_TRANSITION (0x30F)] Error Code 784: A thread is getting dispatched with MCA EXCEPTION because of MCA. [ERROR_MCA_EXCEPTION (0x310)] Error Code 785: Access to %1 is monitored by policy rule %2. [ERROR_ACCESS_AUDIT_BY_POLICY (0x311)] Error Code 786: Access to %1 has been restricted by your Administrator by policy rule %2. [ERROR_ACCESS_DISABLED_NO_SAFER_UI_BY_POLICY (0x312)] Error Code 787: A valid hibernation file has been invalidated and should be abandoned. [ERROR_ABANDON_HIBERFILE (0x313)] Error Code 788:
{Delayed Write Failed} Windows was unable to save all the data for the
file %hs; the data has been lost. This error may be caused by network
connectivity issues. Please try to save this file elsewhere.
[ERROR_LOST_WRITEBEHIND_DATA_NETWORK_DISCONNECTED (0x314)] Error Code 789:
{Delayed Write Failed} Windows was unable to save all the data for the
file %hs; the data has been lost. This error was returned by the server
on which the file exists. Please try to save this file elsewhere.
[ERROR_LOST_WRITEBEHIND_DATA_NETWORK_SERVER_ERROR (0x315)] Error Code 790:
{Delayed Write Failed} Windows was unable to save all the data for the
file %hs; the data has been lost. This error may be caused if the device
has been removed or the media is write-protected.
[ERROR_LOST_WRITEBEHIND_DATA_LOCAL_DISK_ERROR (0x316)] Error Code 791: The resources required for this device conflict with the MCFG table. [ERROR_BAD_MCFG_TABLE (0x317)] Error Code 994: Access to the extended attribute was denied. [ERROR_EA_ACCESS_DENIED (0x3E2)] Error Code 995: The I/O operation has been aborted because of either a thread exit or an application request. [ERROR_OPERATION_ABORTED (0x3E3)] Error Code 996: Overlapped I/O event is not in a signaled state. [ERROR_IO_INCOMPLETE (0x3E4)] Error Code 997: Overlapped I/O operation is in progress. [ERROR_IO_PENDING (0x3E5)] Error Code 998: Invalid access to memory location. [ERROR_NOACCESS (0x3E6)] Error Code 999: Error performing inpage operation. [ERROR_SWAPERROR (0x3E7)] Error Code 1001: Recursion too deep; the stack overflowed. [ERROR_STACK_OVERFLOW (0x3E9)] Error Code 1002: The window cannot act on the sent message. [ERROR_INVALID_MESSAGE (0x3EA)] Error Code 1003: Cannot complete this function. [ERROR_CAN_NOT_COMPLETE (0x3EB)] Error Code 1004: Invalid flags. [ERROR_INVALID_FLAGS (0x3EC)] Error Code 1005:
The volume does not contain a recognized file system. Please make sure
that all required file system drivers are loaded and that the volume is
not corrupted. [ERROR_UNRECOGNIZED_VOLUME (0x3ED)] Error Code 1006: The volume for a file has been externally altered so that the opened file is no longer valid. [ERROR_FILE_INVALID (0x3EE)] Error Code 1007: The requested operation cannot be performed in full-screen mode. [ERROR_FULLSCREEN_MODE (0x3EF)] Error Code 1008: An attempt was made to reference a token that does not exist. [ERROR_NO_TOKEN (0x3F0)] Error Code 1009: The configuration registry database is corrupt. [ERROR_BADDB (0x3F1)] Error Code 1010: The configuration registry key is invalid. [ERROR_BADKEY (0x3F2)] Error Code 1011: The configuration registry key could not be opened. [ERROR_CANTOPEN (0x3F3)] Error Code 1012: The configuration registry key could not be read. [ERROR_CANTREAD (0x3F4)] Error Code 1013: The configuration registry key could not be written. [ERROR_CANTWRITE (0x3F5)] Error Code 1014:
One of the files in the registry database had to be recovered by use of
a log or alternate copy. The recovery was successful.
[ERROR_REGISTRY_RECOVERED (0x3F6)] Error Code 1015:
The registry is corrupted. The structure of one of the files containing
registry data is corrupted or the system's memory image of the file is
corrupted or the file could not be recovered because the alternate copy
or log was absent or corrupted. [ERROR_REGISTRY_CORRUPT (0x3F7)] Error Code 1016:
An I/O operation initiated by the registry failed unrecoverably. The
registry could not read in or write out or flush one of the files that
contain the system's image of the registry. [ERROR_REGISTRY_IO_FAILED
(0x3F8)] Error Code 1017: The system
has attempted to load or restore a file into the registry but the
specified file is not in a registry file format.
[ERROR_NOT_REGISTRY_FILE (0x3F9)] Error Code 1018: Illegal operation attempted on a registry key that has been marked for deletion. [ERROR_KEY_DELETED (0x3FA)] Error Code 1019: System could not allocate the required space in a registry log. [ERROR_NO_LOG_SPACE (0x3FB)] Error Code 1020: Cannot create a symbolic link in a registry key that already has subkeys or values. [ERROR_KEY_HAS_CHILDREN (0x3FC)] Error Code 1021: Cannot create a stable subkey under a volatile parent key. [ERROR_CHILD_MUST_BE_VOLATILE (0x3FD)] Error Code 1022:
A notify change request is being completed and the information is not
being returned in the caller's buffer. The caller now needs to enumerate
the files to find the changes. [ERROR_NOTIFY_ENUM_DIR (0x3FE)] Error Code 1051:
A stop control has been sent to a service that other running services
are dependent on. [ERROR_DEPENDENT_SERVICES_RUNNING (0x41B)] Error Code 1052: The requested control is not valid for this service. [ERROR_INVALID_SERVICE_CONTROL (0x41C)] Error Code 1053: The service did not respond to the start or control request in a timely fashion. [ERROR_SERVICE_REQUEST_TIMEOUT (0x41D)] Error Code 1054: A thread could not be created for the service. [ERROR_SERVICE_NO_THREAD (0x41E)] Error Code 1055: The service database is locked. [ERROR_SERVICE_DATABASE_LOCKED (0x41F)] Error Code 1056: An instance of the service is already running. [ERROR_SERVICE_ALREADY_RUNNING (0x420)] Error Code 1057:
The account name is invalid or does not exist or the password is
invalid for the account name specified. [ERROR_INVALID_SERVICE_ACCOUNT
(0x421)] Error Code 1058: The service
cannot be started either because it is disabled or because it has no
enabled devices associated with it. [ERROR_SERVICE_DISABLED (0x422)] Error Code 1059: Circular service dependency was specified. [ERROR_CIRCULAR_DEPENDENCY (0x423)] Error Code 1060: The specified service does not exist as an installed service. [ERROR_SERVICE_DOES_NOT_EXIST (0x424)] Error Code 1061: The service cannot accept control messages at this time. [ERROR_SERVICE_CANNOT_ACCEPT_CTRL (0x425)] Error Code 1062: The service has not been started. [ERROR_SERVICE_NOT_ACTIVE (0x426)] Error Code 1063: The service process could not connect to the service controller. [ERROR_FAILED_SERVICE_CONTROLLER_CONNECT (0x427)] Error Code 1064: An exception occurred in the service when handling the control request. [ERROR_EXCEPTION_IN_SERVICE (0x428)] Error Code 1065: The database specified does not exist. [ERROR_DATABASE_DOES_NOT_EXIST (0x429)] Error Code 1066: The service has returned a service-specific error code. [ERROR_SERVICE_SPECIFIC_ERROR (0x42A)] Error Code 1067: The process terminated unexpectedly. [ERROR_PROCESS_ABORTED (0x42B)] Error Code 1068: The dependency service or group failed to start. [ERROR_SERVICE_DEPENDENCY_FAIL (0x42C)] Error Code 1069: The service did not start due to a logon failure. [ERROR_SERVICE_LOGON_FAILED (0x42D)] Error Code 1070: After starting the service hung in a start-pending state. [ERROR_SERVICE_START_HANG (0x42E)] Error Code 1071: The specified service database lock is invalid. [ERROR_INVALID_SERVICE_LOCK (0x42F)] Error Code 1072: The specified service has been marked for deletion. [ERROR_SERVICE_MARKED_FOR_DELETE (0x430)] Error Code 1073: The specified service already exists. [ERROR_SERVICE_EXISTS (0x431)] Error Code 1074: The system is currently running with the last-known-good configuration. [ERROR_ALREADY_RUNNING_LKG (0x432)] Error Code 1075: The dependency service does not exist or has been marked for deletion. [ERROR_SERVICE_DEPENDENCY_DELETED (0x433)] Error Code 1076: The current boot has already been accepted for use as the last-known-good control set. [ERROR_BOOT_ALREADY_ACCEPTED (0x434)] Error Code 1077: No attempts to start the service have been made since the last boot. [ERROR_SERVICE_NEVER_STARTED (0x435)] Error Code 1078: The name is already in use as either a service name or a service display name. [ERROR_DUPLICATE_SERVICE_NAME (0x436)] Error Code 1079:
The account specified for this service is different from the account
specified for other services running in the same process.
[ERROR_DIFFERENT_SERVICE_ACCOUNT (0x437)] Error Code 1080: Failure actions can only be set for Win32 services not for drivers. [ERROR_CANNOT_DETECT_DRIVER_FAILURE (0x438)] Error Code 1081:
This service runs in the same process as the service control manager.
Therefore the service control manager cannot take action if this
service's process terminates unexpectedly.
[ERROR_CANNOT_DETECT_PROCESS_ABORT (0x439)] Error Code 1082: No recovery program has been configured for this service. [ERROR_NO_RECOVERY_PROGRAM (0x43A)] Error Code 1083:
The executable program that this service is configured to run in does
not implement the service. [ERROR_SERVICE_NOT_IN_EXE (0x43B)] Error Code 1084: This service cannot be started in Safe Mode [ERROR_NOT_SAFEBOOT_SERVICE (0x43C)] Error Code 1100: The physical end of the tape has been reached. [ERROR_END_OF_MEDIA (0x44C)] Error Code 1101: A tape access reached a filemark. [ERROR_FILEMARK_DETECTED (0x44D)] Error Code 1102: The beginning of the tape or a partition was encountered. [ERROR_BEGINNING_OF_MEDIA (0x44E)] Error Code 1103: A tape access reached the end of a set of files. [ERROR_SETMARK_DETECTED (0x44F)] Error Code 1104: No more data is on the tape. [ERROR_NO_DATA_DETECTED (0x450)] Error Code 1105: Tape could not be partitioned. [ERROR_PARTITION_FAILURE (0x451)] Error Code 1106: When accessing a new tape of a multivolume partition the current block size is incorrect. [ERROR_INVALID_BLOCK_LENGTH (0x452)] Error Code 1107: Tape partition information could not be found when loading a tape. [ERROR_DEVICE_NOT_PARTITIONED (0x453)] Error Code 1108: Unable to lock the media eject mechanism. [ERROR_UNABLE_TO_LOCK_MEDIA (0x454)] Error Code 1109: Unable to unload the media. [ERROR_UNABLE_TO_UNLOAD_MEDIA (0x455)] Error Code 1110: The media in the drive may have changed. [ERROR_MEDIA_CHANGED (0x456)] Error Code 1111: The I/O bus was reset. [ERROR_BUS_RESET (0x457)] Error Code 1112: No media in drive. [ERROR_NO_MEDIA_IN_DRIVE (0x458)] Error Code 1113: No mapping for the Unicode character exists in the target multi-byte code page. [ERROR_NO_UNICODE_TRANSLATION (0x459)] Error Code 1114: A dynamic link library (DLL) initialization routine failed. [ERROR_DLL_INIT_FAILED (0x45A)] Error Code 1115: A system shutdown is in progress. [ERROR_SHUTDOWN_IN_PROGRESS (0x45B)] Error Code 1116: Unable to abort the system shutdown because no shutdown was in progress. [ERROR_NO_SHUTDOWN_IN_PROGRESS (0x45C)] Error Code 1117: The request could not be performed because of an I/O device error. [ERROR_IO_DEVICE (0x45D)] Error Code 1118: No serial device was successfully initialized. The serial driver will unload. [ERROR_SERIAL_NO_DEVICE (0x45E)] 1 - 1118 | 1119 - 1935 | 1936 - 8250 | 8251 - 12008 | 12009 - 15841
System error codes will appear in software programs and in various areas within the Windows operating system after certain errors occur.1
Unfortunately, sometimes all you get is the system error code but nothing about what the code means! Once you know what the system error code means (below) then you can work on fixing the problem.
Unfortunately, sometimes all you get is the system error code but nothing about what the code means! Once you know what the system error code means (below) then you can work on fixing the problem.
| 1 - 1118 | 1119 - 1935 | 1936 - 8250 | 8251 - 12008 | 12009 - 15841 | |
| Error Code 1: Incorrect function. [ERROR_INVALID_FUNCTION (0x1)] | |
| Error Code 2: The system cannot find the file specified. [ERROR_FILE_NOT_FOUND (0x2)] | |
| Error Code 3: The system cannot find the path specified. [ERROR_PATH_NOT_FOUND (0x3)] | |
| Error Code 4: The system cannot open the file. [ERROR_TOO_MANY_OPEN_FILES (0x4)] | |
| Error Code 5: Access is denied. [ERROR_ACCESS_DENIED (0x5)] | |
| Error Code 6: The handle is invalid. [ERROR_INVALID_HANDLE (0x6)] | |
| Error Code 7: The storage control blocks were destroyed. [ERROR_ARENA_TRASHED (0x7)] | |
| Error Code 8: Not enough storage is available to process this command. [ERROR_NOT_ENOUGH_MEMORY (0x8)] | |
| Error Code 9: The storage control block address is invalid. [ERROR_INVALID_BLOCK (0x9)] | |
| Error Code 10: The environment is incorrect. [ERROR_BAD_ENVIRONMENT (0xA)] | |
| Error Code 11: An attempt was made to load a program with an incorrect format. [ERROR_BAD_FORMAT (0xB)] | |
| Error Code 12: The access code is invalid. [ERROR_INVALID_ACCESS (0xC)] | |
| Error Code 13: The data is invalid. [ERROR_INVALID_DATA (0xD)] | |
| Error Code 14: Not enough storage is available to complete this operation. [ERROR_OUTOFMEMORY (0xE)] | |
| Error Code 15: The system cannot find the drive specified. [ERROR_INVALID_DRIVE (0xF)] | |
| Error Code 16: The directory cannot be removed. [ERROR_CURRENT_DIRECTORY (0x10)] | |
| Error Code 17: The system cannot move the file to a different disk drive. [ERROR_NOT_SAME_DEVICE (0x11)] | |
| Error Code 18: There are no more files. [ERROR_NO_MORE_FILES (0x12)] | |
| Error Code 19: The media is write protected. [ERROR_WRITE_PROTECT (0x13)] | |
| Error Code 20: The system cannot find the device specified. [ERROR_BAD_UNIT (0x14)] | |
| Error Code 21: The device is not ready. [ERROR_NOT_READY (0x15)] | |
| Error Code 22: The device does not recognize the command. [ERROR_BAD_COMMAND (0x16)] | |
| Error Code 23: Data error (cyclic redundancy check). [ERROR_CRC (0x17)] | |
| Error Code 24: The program issued a command but the command length is incorrect. [ERROR_BAD_LENGTH (0x18)] | |
| Error Code 25: The drive cannot locate a specific area or track on the disk. [ERROR_SEEK (0x19)] | |
| Error Code 26: The specified disk or diskette cannot be accessed. [ERROR_NOT_DOS_DISK (0x1A)] | |
| Error Code 27: The drive cannot find the sector requested. [ERROR_SECTOR_NOT_FOUND (0x1B)] | |
| Error Code 28: The printer is out of paper. [ERROR_OUT_OF_PAPER (0x1C)] | |
| Error Code 29: The system cannot write to the specified device. [ERROR_WRITE_FAULT (0x1D)] | |
| Error Code 30: The system cannot read from the specified device. [ERROR_READ_FAULT (0x1E)] | |
| Error Code 31: A device attached to the system is not functioning. [ERROR_GEN_FAILURE (0x1F)] | |
| Error Code 32: The process cannot access the file because it is being used by another process. [ERROR_SHARING_VIOLATION (0x20)] | |
| Error Code 33: The process cannot access the file because another process has locked a portion of the file. [ERROR_LOCK_VIOLATION (0x21)] | |
| Error Code 34: The wrong diskette is in the drive. Insert %2 (Volume Serial Number: %3) into drive %1. [ERROR_WRONG_DISK (0x22)] | |
| Error Code 36: Too many files opened for sharing. [ERROR_SHARING_BUFFER_EXCEEDED (0x24)] | |
| Error Code 38: Reached the end of the file. [ERROR_HANDLE_EOF (0x26)] | |
| Error Code 39: The disk is full. [ERROR_HANDLE_DISK_FULL (0x27)] | |
| Error Code 50: The request is not supported. [ERROR_NOT_SUPPORTED (0x32)] | |
| Error Code 51: Windows cannot find the network path. Verify that the network path is correct and the destination computer is not busy or turned off. If Windows still cannot find the network path contact your network administrator. [ERROR_REM_NOT_LIST (0x33)] | |
| Error Code 52: You were not connected because a duplicate name exists on the network. If joining a domain, go to System in Control Panel to change the computer name and try again. If joining a workgroup choose another workgroup name. [ERROR_DUP_NAME (0x34)] | |
| Error Code 53: The network path was not found. [ERROR_BAD_NETPATH (0x35)] | |
| Error Code 54: The network is busy. [ERROR_NETWORK_BUSY (0x36)] | |
| Error Code 55: The specified network resource or device is no longer available. [ERROR_DEV_NOT_EXIST (0x37)] | |
| Error Code 56: The network BIOS command limit has been reached. [ERROR_TOO_MANY_CMDS (0x38)] | |
| Error Code 57: A network adapter hardware error occurred. [ERROR_ADAP_HDW_ERR (0x39)] | |
| Error Code 58: The specified server cannot perform the requested operation. [ERROR_BAD_NET_RESP (0x3A)] | |
| Error Code 59: An unexpected network error occurred. [ERROR_UNEXP_NET_ERR (0x3B)] | |
| Error Code 60: The remote adapter is not compatible. [ERROR_BAD_REM_ADAP (0x3C)] | |
| Error Code 61: The printer queue is full. [ERROR_PRINTQ_FULL (0x3D)] | |
| Error Code 62: Space to store the file waiting to be printed is not available on the server. [ERROR_NO_SPOOL_SPACE (0x3E)] | |
| Error Code 63: Your file waiting to be printed was deleted. [ERROR_PRINT_CANCELLED (0x3F)] | |
| Error Code 64: The specified network name is no longer available. [ERROR_NETNAME_DELETED (0x40)] | |
| Error Code 65: Network access is denied. [ERROR_NETWORK_ACCESS_DENIED (0x41)] | |
| Error Code 66: The network resource type is not correct. [ERROR_BAD_DEV_TYPE (0x42)] | |
| Error Code 67: The network name cannot be found. [ERROR_BAD_NET_NAME (0x43)] | |
| Error Code 68: The name limit for the local computer network adapter card was exceeded. [ERROR_TOO_MANY_NAMES (0x44)] | |
| Error Code 69: The network BIOS session limit was exceeded. [ERROR_TOO_MANY_SESS (0x45)] | |
| Error Code 70: The remote server has been paused or is in the process of being started. [ERROR_SHARING_PAUSED (0x46)] | |
| Error Code 71: No more connections can be made to this remote computer at this time because there are already as many connections as the computer can accept. [ERROR_REQ_NOT_ACCEP (0x47)] | |
| Error Code 72: The specified printer or disk device has been paused. [ERROR_REDIR_PAUSED (0x48)] | |
| Error Code 80: The file exists. [ERROR_FILE_EXISTS (0x50)] | |
| Error Code 82: The directory or file cannot be created. [ERROR_CANNOT_MAKE (0x52)] | |
| Error Code 83: Fail on INT 24. [ERROR_FAIL_I24 (0x53)] | |
| Error Code 84: Storage to process this request is not available. [ERROR_OUT_OF_STRUCTURES (0x54)] | |
| Error Code 85: The local device name is already in use. [ERROR_ALREADY_ASSIGNED (0x55)] | |
| Error Code 86: The specified network password is not correct. [ERROR_INVALID_PASSWORD (0x56)] | |
| Error Code 87: The parameter is incorrect. [ERROR_INVALID_PARAMETER (0x57)] | |
| Error Code 88: A write fault occurred on the network. [ERROR_NET_WRITE_FAULT (0x58)] | |
| Error Code 89: The system cannot start another process at this time. [ERROR_NO_PROC_SLOTS (0x59)] | |
| Error Code 100: Cannot create another system semaphore. [ERROR_TOO_MANY_SEMAPHORES (0x64)] | |
| Error Code 101: The exclusive semaphore is owned by another process. [ERROR_EXCL_SEM_ALREADY_OWNED (0x65)] | |
| Error Code 102: The semaphore is set and cannot be closed. [ERROR_SEM_IS_SET (0x66)] | |
| Error Code 103: The semaphore cannot be set again. [ERROR_TOO_MANY_SEM_REQUESTS (0x67)] | |
| Error Code 104: Cannot request exclusive semaphores at interrupt time. [ERROR_INVALID_AT_INTERRUPT_TIME (0x68)] | |
| Error Code 105: The previous ownership of this semaphore has ended. [ERROR_SEM_OWNER_DIED (0x69)] | |
| Error Code 106: Insert the diskette for drive %1. [ERROR_SEM_USER_LIMIT (0x6A)] | |
| Error Code 107: The program stopped because an alternate diskette was not inserted. [ERROR_DISK_CHANGE (0x6B)] | |
| Error Code 108: The disk is in use or locked by another process. [ERROR_DRIVE_LOCKED (0x6C)] | |
| Error Code 109: The pipe has been ended. [ERROR_BROKEN_PIPE (0x6D)] | |
| Error Code 110: The system cannot open the device or file specified. [ERROR_OPEN_FAILED (0x6E)] | |
| Error Code 111: The file name is too long. [ERROR_BUFFER_OVERFLOW (0x6F)] | |
| Error Code 112: There is not enough space on the disk. [ERROR_DISK_FULL (0x70)] | |
| Error Code 113: No more internal file identifiers available. [ERROR_NO_MORE_SEARCH_HANDLES (0x71)] | |
| Error Code 114: The target internal file identifier is incorrect. [ERROR_INVALID_TARGET_HANDLE (0x72)] | |
| Error Code 117: The IOCTL call made by the application program is not correct. [ERROR_INVALID_CATEGORY (0x75)] | |
| Error Code 118: The verify-on-write switch parameter value is not correct. [ERROR_INVALID_VERIFY_SWITCH (0x76)] | |
| Error Code 119: The system does not support the command requested. [ERROR_BAD_DRIVER_LEVEL (0x77)] | |
| Error Code 120: This function is not supported on this system. [ERROR_CALL_NOT_IMPLEMENTED (0x78)] | |
| Error Code 121: The semaphore timeout period has expired. [ERROR_SEM_TIMEOUT (0x79)] | |
| Error Code 122: The data area passed to a system call is too small. [ERROR_INSUFFICIENT_BUFFER (0x7A)] | |
| Error Code 123: The filename, directory name or volume label syntax is incorrect. [ERROR_INVALID_NAME (0x7B)] | |
| Error Code 124: The system call level is not correct. [ERROR_INVALID_LEVEL (0x7C)] | |
| Error Code 125: The disk has no volume label. [ERROR_NO_VOLUME_LABEL (0x7D)] | |
| Error Code 126: The specified module could not be found. [ERROR_MOD_NOT_FOUND (0x7E)] | |
| Error Code 127: The specified procedure could not be found. [ERROR_PROC_NOT_FOUND (0x7F)] | |
| Error Code 128: There are no child processes to wait for. [ERROR_WAIT_NO_CHILDREN (0x80)] | |
| Error Code 129: The %1 application cannot be run in Win32 mode. [ERROR_CHILD_NOT_COMPLETE (0x81)] | |
| Error Code 130: Attempt to use a file handle to an open disk partition for an operation other than raw disk I/O. [ERROR_DIRECT_ACCESS_HANDLE (0x82)] | |
| Error Code 131: An attempt was made to move the file pointer before the beginning of the file. [ERROR_NEGATIVE_SEEK (0x83)] | |
| Error Code 132: The file pointer cannot be set on the specified device or file. [ERROR_SEEK_ON_DEVICE (0x84)] | |
| Error Code 133: A JOIN or SUBST command cannot be used for a drive that contains previously joined drives. [ERROR_IS_JOIN_TARGET (0x85)] | |
| Error Code 134: An attempt was made to use a JOIN or SUBST command on a drive that has already been joined. [ERROR_IS_JOINED (0x86)] | |
| Error Code 135: An attempt was made to use a JOIN or SUBST command on a drive that has already been substituted. [ERROR_IS_SUBSTED (0x87)] | |
| Error Code 136: The system tried to delete the JOIN of a drive that is not joined. [ERROR_NOT_JOINED (0x88)] | |
| Error Code 137: The system tried to delete the substitution of a drive that is not substituted. [ERROR_NOT_SUBSTED (0x89)] | |
| Error Code 138: The system tried to join a drive to a directory on a joined drive. [ERROR_JOIN_TO_JOIN (0x8A)] | |
| Error Code 139: The system tried to substitute a drive to a directory on a substituted drive. [ERROR_SUBST_TO_SUBST (0x8B)] | |
| Error Code 140: The system tried to join a drive to a directory on a substituted drive. [ERROR_JOIN_TO_SUBST (0x8C)] | |
| Error Code 141: The system tried to SUBST a drive to a directory on a joined drive. [ERROR_SUBST_TO_JOIN (0x8D)] | |
| Error Code 142: The system cannot perform a JOIN or SUBST at this time. [ERROR_BUSY_DRIVE (0x8E)] | |
| Error Code 143: The system cannot join or substitute a drive to or for a directory on the same drive. [ERROR_SAME_DRIVE (0x8F)] | |
| Error Code 144: The directory is not a subdirectory of the root directory. [ERROR_DIR_NOT_ROOT (0x90)] | |
| Error Code 145: The directory is not empty. [ERROR_DIR_NOT_EMPTY (0x91)] | |
| Error Code 146: The path specified is being used in a substitute. [ERROR_IS_SUBST_PATH (0x92)] | |
| Error Code 147: Not enough resources are available to process this command. [ERROR_IS_JOIN_PATH (0x93)] | |
| Error Code 148: The path specified cannot be used at this time. [ERROR_PATH_BUSY (0x94)] | |
| Error Code 149: An attempt was made to join or substitute a drive for which a directory on the drive is the target of a previous substitute. [ERROR_IS_SUBST_TARGET (0x95)] | |
| Error Code 150: System trace information was not specified in your CONFIG.SYS file or tracing is disallowed. [ERROR_SYSTEM_TRACE (0x96)] | |
| Error Code 151: The number of specified semaphore events for DosMuxSemWait is not correct. [ERROR_INVALID_EVENT_COUNT (0x97)] | |
| Error Code 152: DosMuxSemWait did not execute too many semaphores are already set. [ERROR_TOO_MANY_MUXWAITERS (0x98)] | |
| Error Code 153: The DosMuxSemWait list is not correct. [ERROR_INVALID_LIST_FORMAT (0x99)] | |
| Error Code 154: The volume label you entered exceeds the label character limit of the target file system. [ERROR_LABEL_TOO_LONG (0x9A)] | |
| Error Code 155: Cannot create another thread. [ERROR_TOO_MANY_TCBS (0x9B)] | |
| Error Code 156: The recipient process has refused the signal. [ERROR_SIGNAL_REFUSED (0x9C)] | |
| Error Code 157: The segment is already discarded and cannot be locked. [ERROR_DISCARDED (0x9D)] | |
| Error Code 158: The segment is already unlocked. [ERROR_NOT_LOCKED (0x9E)] | |
| Error Code 159: The address for the thread ID is not correct. [ERROR_BAD_THREADID_ADDR (0x9F)] | |
| Error Code 160: One or more arguments are not correct. [ERROR_BAD_ARGUMENTS (0xA0)] | |
| Error Code 161: The specified path is invalid. [ERROR_BAD_PATHNAME (0xA1)] | |
| Error Code 162: A signal is already pending. [ERROR_SIGNAL_PENDING (0xA2)] | |
| Error Code 164: No more threads can be created in the system. [ERROR_MAX_THRDS_REACHED (0xA4)] | |
| Error Code 167: Unable to lock a region of a file. [ERROR_LOCK_FAILED (0xA7)] | |
| Error Code 170: The requested resource is in use. [ERROR_BUSY (0xAA)] | |
| Error Code 173: A lock request was not outstanding for the supplied cancel region. [ERROR_CANCEL_VIOLATION (0xAD)] | |
| Error Code 174: The file system does not support atomic changes to the lock type. [ERROR_ATOMIC_LOCKS_NOT_SUPPORTED (0xAE)] | |
| Error Code 180: The system detected a segment number that was not correct. [ERROR_INVALID_SEGMENT_NUMBER (0xB4)] | |
| Error Code 182: The operating system cannot run %1. [ERROR_INVALID_ORDINAL (0xB6)] | |
| Error Code 183: Cannot create a file when that file already exists. [ERROR_ALREADY_EXISTS (0xB7)] | |
| Error Code 186: The flag passed is not correct. [ERROR_INVALID_FLAG_NUMBER (0xBA)] | |
| Error Code 187: The specified system semaphore name was not found. [ERROR_SEM_NOT_FOUND (0xBB)] | |
| Error Code 188: The operating system cannot run %1. [ERROR_INVALID_STARTING_CODESEG (0xBC)] | |
| Error Code 189: The operating system cannot run %1. [ERROR_INVALID_STACKSEG (0xBD)] | |
| Error Code 190: The operating system cannot run %1. [ERROR_INVALID_MODULETYPE (0xBE)] | |
| Error Code 191: Cannot run %1 in Win32 mode. [ERROR_INVALID_EXE_SIGNATURE (0xBF)] | |
| Error Code 192: The operating system cannot run %1. [ERROR_EXE_MARKED_INVALID (0xC0)] | |
| Error Code 193: %1 is not a valid Win32 application. [ERROR_BAD_EXE_FORMAT (0xC1)] | |
| Error Code 194: The operating system cannot run %1. [ERROR_ITERATED_DATA_EXCEEDS_64k (0xC2)] | |
| Error Code 195: The operating system cannot run %1. [ERROR_INVALID_MINALLOCSIZE (0xC3)] | |
| Error Code 196: The operating system cannot run this application program. [ERROR_DYNLINK_FROM_INVALID_RING (0xC4)] | |
| Error Code 197: The operating system is not presently configured to run this application. [ERROR_IOPL_NOT_ENABLED (0xC5)] | |
| Error Code 198: The operating system cannot run %1. [ERROR_INVALID_SEGDPL (0xC6)] | |
| Error Code 199: The operating system cannot run this application program. [ERROR_AUTODATASEG_EXCEEDS_64k (0xC7)] | |
| Error Code 200: The code segment cannot be greater than or equal to 64K. [ERROR_RING2SEG_MUST_BE_MOVABLE (0xC8)] | |
| Error Code 201: The operating system cannot run %1. [ERROR_RELOC_CHAIN_XEEDS_SEGLIM (0xC9)] | |
| Error Code 202: The operating system cannot run %1. [ERROR_INFLOOP_IN_RELOC_CHAIN (0xCA)] | |
| Error Code 203: The system could not find the environment option that was entered. [ERROR_ENVVAR_NOT_FOUND (0xCB)] | |
| Error Code 205: No process in the command subtree has a signal handler. [ERROR_NO_SIGNAL_SENT (0xCD)] | |
| Error Code 206: The filename or extension is too long. [ERROR_FILENAME_EXCED_RANGE (0xCE)] | |
| Error Code 207: The ring 2 stack is in use. [ERROR_RING2_STACK_IN_USE (0xCF)] | |
| Error Code 208: The global filename characters, * or ?, are entered incorrectly or too many global filename characters are specified. [ERROR_META_EXPANSION_TOO_LONG (0xD0)] | |
| Error Code 209: The signal being posted is not correct. [ERROR_INVALID_SIGNAL_NUMBER (0xD1)] | |
| Error Code 210: The signal handler cannot be set. [ERROR_THREAD_1_INACTIVE (0xD2)] | |
| Error Code 212: The segment is locked and cannot be reallocated. [ERROR_LOCKED (0xD4)] | |
| Error Code 214: Too many dynamic-link modules are attached to this program or dynamic-link module. [ERROR_TOO_MANY_MODULES (0xD6)] | |
| Error Code 215: Cannot nest calls to LoadModule. [ERROR_NESTING_NOT_ALLOWED (0xD7)] | |
| Error Code 216: The version of %1 is not compatible with the version you're running. Check your computer's system information to see whether you need a x86 (32-bit) or x64 (64-bit) version of the program, and then contact the software publisher. [ERROR_EXE_MACHINE_TYPE_MISMATCH (0xD8)] | |
| Error Code 217: The image file %1 is signed, unable to modify. [ERROR_EXE_CANNOT_MODIFY_SIGNED_BINARY (0xD9)] | |
| Error Code 218: The image file %1 is strong signed, unable to modify. [ERROR_EXE_CANNOT_MODIFY_STRONG_SIGNED_BINARY (0xDA)] | |
| Error Code 220: This file is checked out or locked for editing by another user. [ERROR_FILE_CHECKED_OUT (0xDC)] | |
| Error Code 221: The file must be checked out before saving changes. [ERROR_CHECKOUT_REQUIRED (0xDD)] | |
| Error Code 222: The file type being saved or retrieved has been blocked. [ERROR_BAD_FILE_TYPE (0xDE)] | |
| Error Code 223: The file size exceeds the limit allowed and cannot be saved. [ERROR_FILE_TOO_LARGE (0xDF)] | |
| Error Code 224: Access Denied. Before opening files in this location, you must first add the web site to your trusted sites list, browse to the web site and select the option to login automatically. [ERROR_FORMS_AUTH_REQUIRED (0xE0)] | |
| Error Code 225: Operation did not complete successfully because the file contains a virus. [ERROR_VIRUS_INFECTED (0xE1)] | |
| Error Code 226: This file contains a virus and cannot be opened. Due to the nature of this virus, the file has been removed from this location. [ERROR_VIRUS_DELETED (0xE2)] | |
| Error Code 229: The pipe is local. [ERROR_PIPE_LOCAL (0xE5)] | |
| Error Code 230: The pipe state is invalid. [ERROR_BAD_PIPE (0xE6)] | |
| Error Code 231: All pipe instances are busy. [ERROR_PIPE_BUSY (0xE7)] | |
| Error Code 232: The pipe is being closed. [ERROR_NO_DATA (0xE8)] | |
| Error Code 233: No process is on the other end of the pipe. [ERROR_PIPE_NOT_CONNECTED (0xE9)] | |
| Error Code 234: More data is available. [ERROR_MORE_DATA (0xEA)] | |
| Error Code 240: The session was canceled. [ERROR_VC_DISCONNECTED (0xF0)] | |
| Error Code 254: The specified extended attribute name was invalid. [ERROR_INVALID_EA_NAME (0xFE)] | |
| Error Code 255: The extended attributes are inconsistent. [ERROR_EA_LIST_INCONSISTENT (0xFF)] | |
| Error Code 258: The wait operation timed out. [WAIT_TIMEOUT (0x102)] | |
| Error Code 259: No more data is available. [ERROR_NO_MORE_ITEMS (0x103)] | |
| Error Code 266: The copy functions cannot be used. [ERROR_CANNOT_COPY (0x10A)] | |
| Error Code 267: The directory name is invalid. [ERROR_DIRECTORY (0x10B)] | |
| Error Code 275: The extended attributes did not fit in the buffer. [ERROR_EAS_DIDNT_FIT (0x113)] | |
| Error Code 276: The extended attribute file on the mounted file system is corrupt. [ERROR_EA_FILE_CORRUPT (0x114)] | |
| Error Code 277: The extended attribute table file is full. [ERROR_EA_TABLE_FULL (0x115)] | |
| Error Code 278: The specified extended attribute handle is invalid. [ERROR_INVALID_EA_HANDLE (0x116)] | |
| Error Code 282: The mounted file system does not support extended attributes. [ERROR_EAS_NOT_SUPPORTED (0x11A)] | |
| Error Code 288: Attempt to release mutex not owned by caller. [ERROR_NOT_OWNER (0x120)] | |
| Error Code 298: Too many posts were made to a semaphore. [ERROR_TOO_MANY_POSTS (0x12A)] | |
| Error Code 299: Only part of a ReadProcessMemory or WriteProcessMemory request was completed. [ERROR_PARTIAL_COPY (0x12B)] | |
| Error Code 300: The oplock request is denied. [ERROR_OPLOCK_NOT_GRANTED (0x12C)] | |
| Error Code 301: An invalid oplock acknowledgment was received by the system. [ERROR_INVALID_OPLOCK_PROTOCOL (0x12D)] | |
| Error Code 302: The volume is too fragmented to complete this operation. [ERROR_DISK_TOO_FRAGMENTED (0x12E)] | |
| Error Code 303: The file cannot be opened because it is in the process of being deleted. [ERROR_DELETE_PENDING (0x12F)] | |
| Error Code 317: The system cannot find message text for message number 0x%1 in the message file for %2. [ERROR_MR_MID_NOT_FOUND (0x13D)] | |
| Error Code 318: The scope specified was not found. [ERROR_SCOPE_NOT_FOUND (0x13E)] | |
| Error Code 350: No action was taken as a system reboot is required. [ERROR_FAIL_NOACTION_REBOOT (0x15E)] | |
| Error Code 351: The shutdown operation failed. [ERROR_FAIL_SHUTDOWN (0x15F)] | |
| Error Code 352: The restart operation failed. [ERROR_FAIL_RESTART (0x160)] | |
| Error Code 353: The maximum number of sessions has been reached. [ERROR_MAX_SESSIONS_REACHED (0x161)] | |
| Error Code 400: The thread is already in background processing mode. [ERROR_THREAD_MODE_ALREADY_BACKGROUND (0x190)] | |
| Error Code 401: The thread is not in background processing mode. [ERROR_THREAD_MODE_NOT_BACKGROUND (0x191)] | |
| Error Code 402: The process is already in background processing mode. [ERROR_PROCESS_MODE_ALREADY_BACKGROUND (0x192)] | |
| Error Code 403: The process is not in background processing mode. [ERROR_PROCESS_MODE_NOT_BACKGROUND (0x193)] | |
| Error Code 487: Attempt to access invalid address. [ERROR_INVALID_ADDRESS (0x1E7)] | |
| Error Code 500: User profile cannot be loaded. [ERROR_USER_PROFILE_LOAD (0x1F4)] | |
| Error Code 534: Arithmetic result exceeded 32 bits. [ERROR_ARITHMETIC_OVERFLOW (0x216)] | |
| Error Code 535: There is a process on other end of the pipe. [ERROR_PIPE_CONNECTED (0x217)] | |
| Error Code 536: Waiting for a process to open the other end of the pipe. [ERROR_PIPE_LISTENING (0x218)] | |
| Error Code 537: Application verifier has found an error in the current process. [ERROR_VERIFIER_STOP (0x219)] | |
| Error Code 538: An error occurred in the ABIOS subsystem. [ERROR_ABIOS_ERROR (0x21A)] | |
| Error Code 539: A warning occurred in the WX86 subsystem. [ERROR_WX86_WARNING (0x21B)] | |
| Error Code 540: An error occurred in the WX86 subsystem. [ERROR_WX86_ERROR (0x21C)] | |
| Error Code 541: An attempt was made to cancel or set a timer that has an associated APC and the subject thread is not the thread that originally set the timer with an associated APC routine. [ERROR_TIMER_NOT_CANCELED (0x21D)] | |
| Error Code 542: Unwind exception code. [ERROR_UNWIND (0x21E)] | |
| Error Code 543: An invalid or unaligned stack was encountered during an unwind operation. [ERROR_BAD_STACK (0x21F)] | |
| Error Code 544: An invalid unwind target was encountered during an unwind operation. [ERROR_INVALID_UNWIND_TARGET (0x220)] | |
| Error Code 545: Invalid Object Attributes specified to NtCreatePort or invalid Port Attributes specified to NtConnectPort [ERROR_INVALID_PORT_ATTRIBUTES (0x221)] | |
| Error Code 546: Length of message passed to NtRequestPort or NtRequestWaitReplyPort was longer than the maximum message allowed by the port. [ERROR_PORT_MESSAGE_TOO_LONG (0x222)] | |
| Error Code 547: An attempt was made to lower a quota limit below the current usage. [ERROR_INVALID_QUOTA_LOWER (0x223)] | |
| Error Code 548: An attempt was made to attach to a device that was already attached to another device. [ERROR_DEVICE_ALREADY_ATTACHED (0x224)] | |
| Error Code 549: An attempt was made to execute an instruction at an unaligned address and the host system does not support unaligned instruction references. [ERROR_INSTRUCTION_MISALIGNMENT (0x225)] | |
| Error Code 550: Profiling not started. [ERROR_PROFILING_NOT_STARTED (0x226)] | |
| Error Code 551: Profiling not stopped. [ERROR_PROFILING_NOT_STOPPED (0x227)] | |
| Error Code 552: The passed ACL did not contain the minimum required information. [ERROR_COULD_NOT_INTERPRET (0x228)] | |
| Error Code 553: The number of active profiling objects is at the maximum and no more may be started. [ERROR_PROFILING_AT_LIMIT (0x229)] | |
| Error Code 554: Used to indicate that an operation cannot continue without blocking for I/O. [ERROR_CANT_WAIT (0x22A)] | |
| Error Code 555: Indicates that a thread attempted to terminate itself by default (called NtTerminateThread with NULL) and it was the last thread in the current process. [ERROR_CANT_TERMINATE_SELF (0x22B)] | |
| Error Code 556: If an MM error is returned which is not defined in the standard FsRtl filter [ERROR_UNEXPECTED_MM_CREATE_ERR (0x22C)] | |
| Error Code 557: If an MM error is returned which is not defined in the standard FsRtl filter [ERROR_UNEXPECTED_MM_MAP_ERROR (0x22D)] | |
| Error Code 558: If an MM error is returned which is not defined in the standard FsRtl filter [ERROR_UNEXPECTED_MM_EXTEND_ERR (0x22E)] | |
| Error Code 559: A malformed function table was encountered during an unwind operation. [ERROR_BAD_FUNCTION_TABLE (0x22F)] | |
| Error Code 560: Indicates that an attempt was made to assign protection to a file system file or directory and one of the SIDs in the security descriptor could not be translated into a GUID that could be stored by the file system. This causes the protection attempt to fail [ERROR_NO_GUID_TRANSLATION (0x230)] | |
| Error Code 561: Indicates that an attempt was made to grow an LDT by setting its size [ERROR_INVALID_LDT_SIZE (0x231)] | |
| Error Code 563: Indicates that the starting value for the LDT information was not an integral multiple of the selector size. [ERROR_INVALID_LDT_OFFSET (0x233)] | |
| Error Code 564: Indicates that the user supplied an invalid descriptor when trying to set up Ldt descriptors. [ERROR_INVALID_LDT_DESCRIPTOR (0x234)] | |
| Error Code 565: Indicates a process has too many threads to perform the requested action. For example [ERROR_TOO_MANY_THREADS (0x235)] | |
| Error Code 566: An attempt was made to operate on a thread within a specific process [ERROR_THREAD_NOT_IN_PROCESS (0x236)] | |
| Error Code 567: Page file quota was exceeded. [ERROR_PAGEFILE_QUOTA_EXCEEDED (0x237)] | |
| Error Code 568: The Netlogon service cannot start because another Netlogon service running in the domain conflicts with the specified role. [ERROR_LOGON_SERVER_CONFLICT (0x238)] | |
| Error Code 569: The SAM database on a Windows Server is significantly out of synchronization with the copy on the Domain Controller. A complete synchronization is required. [ERROR_SYNCHRONIZATION_REQUIRED (0x239)] | |
| Error Code 570: The NtCreateFile API failed. This error should never be returned to an application [ERROR_NET_OPEN_FAILED (0x23A)] | |
| Error Code 571: {Privilege Failed} The I/O permissions for the process could not be changed. [ERROR_IO_PRIVILEGE_FAILED (0x23B)] | |
| Error Code 572: {Application Exit by CTRL+C} The application terminated as a result of a CTRL+C. [ERROR_CONTROL_C_EXIT (0x23C)] | |
| Error Code 573: {Missing System File} The required system file %hs is bad or missing. [ERROR_MISSING_SYSTEMFILE (0x23D)] | |
| Error Code 574: {Application Error} The exception %s (0x%08lx) occurred in the application at location 0x%08lx. [ERROR_UNHANDLED_EXCEPTION (0x23E)] | |
| Error Code 575: {Application Error} The application failed to initialize properly (0x%lx). Click OK to terminate the application. [ERROR_APP_INIT_FAILURE (0x23F)] | |
| Error Code 576: {Unable to Create Paging File} The creation of the paging file %hs failed (%lx). The requested size was %ld. [ERROR_PAGEFILE_CREATE_FAILED (0x240)] | |
| Error Code 577: Windows cannot verify the digital signature for this file. A recent hardware or software change might have installed a file that is signed incorrectly or damaged [ERROR_INVALID_IMAGE_HASH (0x241)] | |
| Error Code 578: {No Paging File Specified} No paging file was specified in the system configuration. [ERROR_NO_PAGEFILE (0x242)] | |
| Error Code 579: {EXCEPTION} A real-mode application issued a floating-point instruction and floating-point hardware is not present. [ERROR_ILLEGAL_FLOAT_CONTEXT (0x243)] | |
| Error Code 580: An event pair synchronization operation was performed using the thread specific client/server event pair object [ERROR_NO_EVENT_PAIR (0x244)] | |
| Error Code 581: A Windows Server has an incorrect configuration. [ERROR_DOMAIN_CTRLR_CONFIG_ERROR (0x245)] | |
| Error Code 582: An illegal character was encountered. For a multi-byte character set this includes a lead byte without a succeeding trail byte. For the Unicode character set this includes the characters 0xFFFF and 0xFFFE. [ERROR_ILLEGAL_CHARACTER (0x246)] | |
| Error Code 583: The Unicode character is not defined in the Unicode character set installed on the system. [ERROR_UNDEFINED_CHARACTER (0x247)] | |
| Error Code 584: The paging file cannot be created on a floppy diskette. [ERROR_FLOPPY_VOLUME (0x248)] | |
| Error Code 585: The system BIOS failed to connect a system interrupt to the device or bus for which the device is connected. [ERROR_BIOS_FAILED_TO_CONNECT_INTERRUPT (0x249)] | |
| Error Code 586: This operation is only allowed for the Primary Domain Controller of the domain. [ERROR_BACKUP_CONTROLLER (0x24A)] | |
| Error Code 587: An attempt was made to acquire a mutant such that its maximum count would have been exceeded. [ERROR_MUTANT_LIMIT_EXCEEDED (0x24B)] | |
| Error Code 588: A volume has been accessed for which a file system driver is required that has not yet been loaded. [ERROR_FS_DRIVER_REQUIRED (0x24C)] | |
| Error Code 589: {Registry File Failure} The registry cannot load the hive (file): %hs or its log or alternate. It is corrupt [ERROR_CANNOT_LOAD_REGISTRY_FILE (0x24D)] | |
| Error Code 590: {Unexpected Failure in DebugActiveProcess} An unexpected failure occurred while processing a DebugActiveProcess API request. You may choose OK to terminate the process [ERROR_DEBUG_ATTACH_FAILED (0x24E)] | |
| Error Code 591: {Fatal System Error} The %hs system process terminated unexpectedly with a status of 0x%08x (0x%08x 0x%08x). The system has been shut down. [ERROR_SYSTEM_PROCESS_TERMINATED (0x24F)] | |
| Error Code 592: {Data Not Accepted} The TDI client could not handle the data received during an indication. [ERROR_DATA_NOT_ACCEPTED (0x250)] | |
| Error Code 593: NTVDM encountered a hard error. [ERROR_VDM_HARD_ERROR (0x251)] | |
| Error Code 594: {Cancel Timeout} The driver %hs failed to complete a canceled I/O request in the allotted time. [ERROR_DRIVER_CANCEL_TIMEOUT (0x252)] | |
| Error Code 595: {Reply Message Mismatch} An attempt was made to reply to an LPC message [ERROR_REPLY_MESSAGE_MISMATCH (0x253)] | |
| Error Code 596: {Delayed Write Failed} Windows was unable to save all the data for the file %hs. The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. [ERROR_LOST_WRITEBEHIND_DATA (0x254)] | |
| Error Code 597: The parameter(s) passed to the server in the client/server shared memory window were invalid. Too much data may have been put in the shared memory window. [ERROR_CLIENT_SERVER_PARAMETERS_INVALID (0x255)] | |
| Error Code 598: The stream is not a tiny stream. [ERROR_NOT_TINY_STREAM (0x256)] | |
| Error Code 599: The request must be handled by the stack overflow code. [ERROR_STACK_OVERFLOW_READ (0x257)] | |
| Error Code 600: Internal OFS status codes indicating how an allocation operation is handled. Either it is retried after the containing onode is moved or the extent stream is converted to a large stream. [ERROR_CONVERT_TO_LARGE (0x258)] | |
| Error Code 601: The attempt to find the object found an object matching by ID on the volume but it is out of the scope of the handle used for the operation. [ERROR_FOUND_OUT_OF_SCOPE (0x259)] | |
| Error Code 602: The bucket array must be grown. Retry transaction after doing so. [ERROR_ALLOCATE_BUCKET (0x25A)] | |
| Error Code 603: The user/kernel marshalling buffer has overflowed. [ERROR_MARSHALL_OVERFLOW (0x25B)] | |
| Error Code 604: The supplied variant structure contains invalid data. [ERROR_INVALID_VARIANT (0x25C)] | |
| Error Code 605: The specified buffer contains ill-formed data. [ERROR_BAD_COMPRESSION_BUFFER (0x25D)] | |
| Error Code 606: {Audit Failed} An attempt to generate a security audit failed. [ERROR_AUDIT_FAILED (0x25E)] | |
| Error Code 607: The timer resolution was not previously set by the current process. [ERROR_TIMER_RESOLUTION_NOT_SET (0x25F)] | |
| Error Code 608: There is insufficient account information to log you on. [ERROR_INSUFFICIENT_LOGON_INFO (0x260)] | |
| Error Code 609: {Invalid DLL Entrypoint} The dynamic link library %hs is not written correctly. The stack pointer has been left in an inconsistent state. The entrypoint should be declared as WINAPI or STDCALL. Select YES to fail the DLL load. Select NO to continue execution. Selecting NO may cause the application to operate incorrectly. [ERROR_BAD_DLL_ENTRYPOINT (0x261)] | |
| Error Code 610: {Invalid Service Callback Entrypoint} The %hs service is not written correctly. The stack pointer has been left in an inconsistent state. The callback entrypoint should be declared as WINAPI or STDCALL. Selecting OK will cause the service to continue operation. However [ERROR_BAD_SERVICE_ENTRYPOINT (0x262)] | |
| Error Code 611: There is an IP address conflict with another system on the network [ERROR_IP_ADDRESS_CONFLICT1 (0x263)] | |
| Error Code 612: There is an IP address conflict with another system on the network [ERROR_IP_ADDRESS_CONFLICT2 (0x264)] | |
| Error Code 613: {Low On Registry Space} The system has reached the maximum size allowed for the system part of the registry. Additional storage requests will be ignored. [ERROR_REGISTRY_QUOTA_LIMIT (0x265)] | |
| Error Code 614: A callback return system service cannot be executed when no callback is active. [ERROR_NO_CALLBACK_ACTIVE (0x266)] | |
| Error Code 615: The password provided is too short to meet the policy of your user account. Please choose a longer password. [ERROR_PWD_TOO_SHORT (0x267)] | |
| Error Code 616: The policy of your user account does not allow you to change passwords too frequently. This is done to prevent users from changing back to a familiar [ERROR_PWD_TOO_RECENT (0x268)] | |
| Error Code 617: You have attempted to change your password to one that you have used in the past. The policy of your user account does not allow this. Please select a password that you have not previously used. [ERROR_PWD_HISTORY_CONFLICT (0x269)] | |
| Error Code 618: The specified compression format is unsupported. [ERROR_UNSUPPORTED_COMPRESSION (0x26A)] | |
| Error Code 619: The specified hardware profile configuration is invalid. [ERROR_INVALID_HW_PROFILE (0x26B)] | |
| Error Code 620: The specified Plug and Play registry device path is invalid. [ERROR_INVALID_PLUGPLAY_DEVICE_PATH (0x26C)] | |
| Error Code 621: The specified quota list is internally inconsistent with its descriptor. [ERROR_QUOTA_LIST_INCONSISTENT (0x26D)] | |
| Error Code 622: {Windows Evaluation Notification} The evaluation period for this installation of Windows has expired. This system will shutdown in 1 hour. To restore access to this installation of Windows [ERROR_EVALUATION_EXPIRATION (0x26E)] | |
| Error Code 623: {Illegal System DLL Relocation} The system DLL %hs was relocated in memory. The application will not run properly. The relocation occurred because the DLL %hs occupied an address range reserved for Windows system DLLs. The vendor supplying the DLL should be contacted for a new DLL. [ERROR_ILLEGAL_DLL_RELOCATION (0x26F)] | |
| Error Code 624: {DLL Initialization Failed} The application failed to initialize because the window station is shutting down. [ERROR_DLL_INIT_FAILED_LOGOFF (0x270)] | |
| Error Code 625: The validation process needs to continue on to the next step. [ERROR_VALIDATE_CONTINUE (0x271)] | |
| Error Code 626: There are no more matches for the current index enumeration. [ERROR_NO_MORE_MATCHES (0x272)] | |
| Error Code 627: The range could not be added to the range list because of a conflict. [ERROR_RANGE_LIST_CONFLICT (0x273)] | |
| Error Code 628: The server process is running under a SID different than that required by client. [ERROR_SERVER_SID_MISMATCH (0x274)] | |
| Error Code 629: A group marked use for deny only cannot be enabled. [ERROR_CANT_ENABLE_DENY_ONLY (0x275)] | |
| Error Code 630: {EXCEPTION} Multiple floating point faults. [ERROR_FLOAT_MULTIPLE_FAULTS (0x276)] | |
| Error Code 631: {EXCEPTION} Multiple floating point traps. [ERROR_FLOAT_MULTIPLE_TRAPS (0x277)] | |
| Error Code 632: The requested interface is not supported. [ERROR_NOINTERFACE (0x278)] | |
| Error Code 633: {System Standby Failed} The driver %hs does not support standby mode. Updating this driver may allow the system to go to standby mode. [ERROR_DRIVER_FAILED_SLEEP (0x279)] | |
| Error Code 634: The system file %1 has become corrupt and has been replaced. [ERROR_CORRUPT_SYSTEM_FILE (0x27A)] | |
| Error Code 635: {Virtual Memory Minimum Too Low} Your system is low on virtual memory. Windows is increasing the size of your virtual memory paging file. During this process [ERROR_COMMITMENT_MINIMUM (0x27B)] | |
| Error Code 636: A device was removed so enumeration must be restarted. [ERROR_PNP_RESTART_ENUMERATION (0x27C)] | |
| Error Code 637: {Fatal System Error} The system image %s is not properly signed. The file has been replaced with the signed file. The system has been shut down. [ERROR_SYSTEM_IMAGE_BAD_SIGNATURE (0x27D)] | |
| Error Code 638: Device will not start without a reboot. [ERROR_PNP_REBOOT_REQUIRED (0x27E)] | |
| Error Code 639: There is not enough power to complete the requested operation. [ERROR_INSUFFICIENT_POWER (0x27F)] | |
| Error Code 640: ERROR_MULTIPLE_FAULT_VIOLATION [ERROR_MULTIPLE_FAULT_VIOLATION (0x280)] | |
| Error Code 641: The system is in the process of shutting down. [ERROR_SYSTEM_SHUTDOWN (0x281)] | |
| Error Code 642: An attempt to remove a processes DebugPort was made [ERROR_PORT_NOT_SET (0x282)] | |
| Error Code 643: This version of Windows is not compatible with the behavior version of directory forest [ERROR_DS_VERSION_CHECK_FAILURE (0x283)] | |
| Error Code 644: The specified range could not be found in the range list. [ERROR_RANGE_NOT_FOUND (0x284)] | |
| Error Code 646: The driver was not loaded because the system is booting into safe mode. [ERROR_NOT_SAFE_MODE_DRIVER (0x286)] | |
| Error Code 647: The driver was not loaded because it failed it's initialization call. [ERROR_FAILED_DRIVER_ENTRY (0x287)] | |
| Error Code 648: The "%hs" encountered an error while applying power or reading the device configuration. This may be caused by a failure of your hardware or by a poor connection. [ERROR_DEVICE_ENUMERATION_ERROR (0x288)] | |
| Error Code 649: The create operation failed because the name contained at least one mount point which resolves to a volume to which the specified device object is not attached. [ERROR_MOUNT_POINT_NOT_RESOLVED (0x289)] | |
| Error Code 650: The device object parameter is either not a valid device object or is not attached to the volume specified by the file name. [ERROR_INVALID_DEVICE_OBJECT_PARAMETER (0x28A)] | |
| Error Code 651: A Machine Check Error has occurred. Please check the system eventlog for additional information. [ERROR_MCA_OCCURED (0x28B)] | |
| Error Code 652: There was error [%2] processing the driver database. [ERROR_DRIVER_DATABASE_ERROR (0x28C)] | |
| Error Code 653: System hive size has exceeded its limit. [ERROR_SYSTEM_HIVE_TOO_LARGE (0x28D)] | |
| Error Code 654: The driver could not be loaded because a previous version of the driver is still in memory. [ERROR_DRIVER_FAILED_PRIOR_UNLOAD (0x28E)] | |
| Error Code 655: {Volume Shadow Copy Service} Please wait while the Volume Shadow Copy Service prepares volume %hs for hibernation. [ERROR_VOLSNAP_PREPARE_HIBERNATE (0x28F)] | |
| Error Code 656: The system has failed to hibernate (The error code is %hs). Hibernation will be disabled until the system is restarted. [ERROR_HIBERNATION_FAILURE (0x290)] | |
| Error Code 665: The requested operation could not be completed due to a file system limitation [ERROR_FILE_SYSTEM_LIMITATION (0x299)] | |
| Error Code 668: An assertion failure has occurred. [ERROR_ASSERTION_FAILURE (0x29C)] | |
| Error Code 669: An error occurred in the ACPI subsystem. [ERROR_ACPI_ERROR (0x29D)] | |
| Error Code 670: WOW Assertion Error. [ERROR_WOW_ASSERTION (0x29E)] | |
| Error Code 671: A device is missing in the system BIOS MPS table. This device will not be used. Please contact your system vendor for system BIOS update. [ERROR_PNP_BAD_MPS_TABLE (0x29F)] | |
| Error Code 672: A translator failed to translate resources. [ERROR_PNP_TRANSLATION_FAILED (0x2A0)] | |
| Error Code 673: A IRQ translator failed to translate resources. [ERROR_PNP_IRQ_TRANSLATION_FAILED (0x2A1)] | |
| Error Code 674: Driver %2 returned invalid ID for a child device (%3). [ERROR_PNP_INVALID_ID (0x2A2)] | |
| Error Code 675: {Kernel Debugger Awakened} the system debugger was awakened by an interrupt. [ERROR_WAKE_SYSTEM_DEBUGGER (0x2A3)] | |
| Error Code 676: {Handles Closed} Handles to objects have been automatically closed as a result of the requested operation. [ERROR_HANDLES_CLOSED (0x2A4)] | |
| Error Code 677: {Too Much Information} The specified access control list (ACL) contained more information than was expected. [ERROR_EXTRANEOUS_INFORMATION (0x2A5)] | |
| Error Code 678: This warning level status indicates that the transaction state already exists for the registry sub-tree [ERROR_RXACT_COMMIT_NECESSARY (0x2A6)] | |
| Error Code 679: {Media Changed} The media may have changed. [ERROR_MEDIA_CHECK (0x2A7)] | |
| Error Code 680: {GUID Substitution} During the translation of a global identifier (GUID) to a Windows security ID (SID) [ERROR_GUID_SUBSTITUTION_MADE (0x2A8)] | |
| Error Code 681: The create operation stopped after reaching a symbolic link [ERROR_STOPPED_ON_SYMLINK (0x2A9)] | |
| Error Code 682: A long jump has been executed. [ERROR_LONGJUMP (0x2AA)] | |
| Error Code 683: The Plug and Play query operation was not successful. [ERROR_PLUGPLAY_QUERY_VETOED (0x2AB)] | |
| Error Code 684: A frame consolidation has been executed. [ERROR_UNWIND_CONSOLIDATE (0x2AC)] | |
| Error Code 685: {Registry Hive Recovered} Registry hive (file): %hs was corrupted and it has been recovered. Some data might have been lost. [ERROR_REGISTRY_HIVE_RECOVERED (0x2AD)] | |
| Error Code 686: The application is attempting to run executable code from the module %hs. This may be insecure. An alternative [ERROR_DLL_MIGHT_BE_INSECURE (0x2AE)] | |
| Error Code 687: The application is loading executable code from the module %hs. This is secure [ERROR_DLL_MIGHT_BE_INCOMPATIBLE (0x2AF)] | |
| Error Code 688: Debugger did not handle the exception. [ERROR_DBG_EXCEPTION_NOT_HANDLED (0x2B0)] | |
| Error Code 689: Debugger will reply later. [ERROR_DBG_REPLY_LATER (0x2B1)] | |
| Error Code 690: Debugger cannot provide handle. [ERROR_DBG_UNABLE_TO_PROVIDE_HANDLE (0x2B2)] | |
| Error Code 691: Debugger terminated thread. [ERROR_DBG_TERMINATE_THREAD (0x2B3)] | |
| Error Code 692: Debugger terminated process. [ERROR_DBG_TERMINATE_PROCESS (0x2B4)] | |
| Error Code 693: Debugger got control C. [ERROR_DBG_CONTROL_C (0x2B5)] | |
| Error Code 694: Debugger printed exception on control C. [ERROR_DBG_PRINTEXCEPTION_C (0x2B6)] | |
| Error Code 695: Debugger received RIP exception. [ERROR_DBG_RIPEXCEPTION (0x2B7)] | |
| Error Code 696: Debugger received control break. [ERROR_DBG_CONTROL_BREAK (0x2B8)] | |
| Error Code 697: Debugger command communication exception. [ERROR_DBG_COMMAND_EXCEPTION (0x2B9)] | |
| Error Code 698: {Object Exists} An attempt was made to create an object and the object name already existed. [ERROR_OBJECT_NAME_EXISTS (0x2BA)] | |
| Error Code 699: {Thread Suspended} A thread termination occurred while the thread was suspended. The thread was resumed [ERROR_THREAD_WAS_SUSPENDED (0x2BB)] | |
| Error Code 700: {Image Relocated} An image file could not be mapped at the address specified in the image file. Local fixups must be performed on this image. [ERROR_IMAGE_NOT_AT_BASE (0x2BC)] | |
| Error Code 701: This informational level status indicates that a specified registry sub-tree transaction state did not yet exist and had to be created. [ERROR_RXACT_STATE_CREATED (0x2BD)] | |
| Error Code 702: {Segment Load} A virtual DOS machine (VDM) is loading [ERROR_SEGMENT_NOTIFICATION (0x2BE)] | |
| Error Code 703: {Invalid Current Directory} The process cannot switch to the startup current directory %hs. Select OK to set current directory to %hs [ERROR_BAD_CURRENT_DIRECTORY (0x2BF)] | |
| Error Code 704: {Redundant Read} To satisfy a read request [ERROR_FT_READ_RECOVERY_FROM_BACKUP (0x2C0)] | |
| Error Code 705: {Redundant Write} To satisfy a write request [ERROR_FT_WRITE_RECOVERY (0x2C1)] | |
| Error Code 706: {Machine Type Mismatch} The image file %hs is valid [ERROR_IMAGE_MACHINE_TYPE_MISMATCH (0x2C2)] | |
| Error Code 707: {Partial Data Received} The network transport returned partial data to its client. The remaining data will be sent later. [ERROR_RECEIVE_PARTIAL (0x2C3)] | |
| Error Code 708: {Expedited Data Received} The network transport returned data to its client that was marked as expedited by the remote system. [ERROR_RECEIVE_EXPEDITED (0x2C4)] | |
| Error Code 709: {Partial Expedited Data Received} The network transport returned partial data to its client and this data was marked as expedited by the remote system. The remaining data will be sent later. [ERROR_RECEIVE_PARTIAL_EXPEDITED (0x2C5)] | |
| Error Code 710: {TDI Event Done} The TDI indication has completed successfully. [ERROR_EVENT_DONE (0x2C6)] | |
| Error Code 711: {TDI Event Pending} The TDI indication has entered the pending state. [ERROR_EVENT_PENDING (0x2C7)] | |
| Error Code 712: Checking file system on %wZ [ERROR_CHECKING_FILE_SYSTEM (0x2C8)] | |
| Error Code 713: {Fatal Application Exit} %hs [ERROR_FATAL_APP_EXIT (0x2C9)] | |
| Error Code 714: The specified registry key is referenced by a predefined handle. [ERROR_PREDEFINED_HANDLE (0x2CA)] | |
| Error Code 715: {Page Unlocked} The page protection of a locked page was changed to 'No Access' and the page was unlocked from memory and from the process. [ERROR_WAS_UNLOCKED (0x2CB)] | |
| Error Code 716: %hs [ERROR_SERVICE_NOTIFICATION (0x2CC)] | |
| Error Code 717: {Page Locked} One of the pages to lock was already locked. [ERROR_WAS_LOCKED (0x2CD)] | |
| Error Code 718: Application popup: %1 : %2 [ERROR_LOG_HARD_ERROR (0x2CE)] | |
| Error Code 719: ERROR_ALREADY_WIN32 [ERROR_ALREADY_WIN32 (0x2CF)] | |
| Error Code 720: {Machine Type Mismatch} The image file %hs is valid [ERROR_IMAGE_MACHINE_TYPE_MISMATCH_EXE (0x2D0)] | |
| Error Code 721: A yield execution was performed and no thread was available to run. [ERROR_NO_YIELD_PERFORMED (0x2D1)] | |
| Error Code 722: The resumable flag to a timer API was ignored. [ERROR_TIMER_RESUME_IGNORED (0x2D2)] | |
| Error Code 723: The arbiter has deferred arbitration of these resources to its parent [ERROR_ARBITRATION_UNHANDLED (0x2D3)] | |
| Error Code 724: The inserted CardBus device cannot be started because of a configuration error on "%hs". [ERROR_CARDBUS_NOT_SUPPORTED (0x2D4)] | |
| Error Code 725: The CPUs in this multiprocessor system are not all the same revision level. To use all processors the operating system restricts itself to the features of the least capable processor in the system. Should problems occur with this system [ERROR_MP_PROCESSOR_MISMATCH (0x2D5)] | |
| Error Code 726: The system was put into hibernation. [ERROR_HIBERNATED (0x2D6)] | |
| Error Code 727: The system was resumed from hibernation. [ERROR_RESUME_HIBERNATION (0x2D7)] | |
| Error Code 728: Windows has detected that the system firmware (BIOS) was updated [previous firmware date = %2 [ERROR_FIRMWARE_UPDATED (0x2D8)] | |
| Error Code 729: A device driver is leaking locked I/O pages causing system degradation. The system has automatically enabled tracking code in order to try and catch the culprit. [ERROR_DRIVERS_LEAKING_LOCKED_PAGES (0x2D9)] | |
| Error Code 730: The system has awoken [ERROR_WAKE_SYSTEM (0x2DA)] | |
| Error Code 731: ERROR_WAIT_1 [ERROR_WAIT_1 (0x2DB)] | |
| Error Code 732: ERROR_WAIT_2 [ERROR_WAIT_2 (0x2DC)] | |
| Error Code 733: ERROR_WAIT_3 [ERROR_WAIT_3 (0x2DD)] | |
| Error Code 734: ERROR_WAIT_63 [ERROR_WAIT_63 (0x2DE)] | |
| Error Code 735: ERROR_ABANDONED_WAIT_0 [ERROR_ABANDONED_WAIT_0 (0x2DF)] | |
| Error Code 736: ERROR_ABANDONED_WAIT_63 [ERROR_ABANDONED_WAIT_63 (0x2E0)] | |
| Error Code 737: ERROR_USER_APC [ERROR_USER_APC (0x2E1)] | |
| Error Code 738: ERROR_KERNEL_APC [ERROR_KERNEL_APC (0x2E2)] | |
| Error Code 739: ERROR_ALERTED [ERROR_ALERTED (0x2E3)] | |
| Error Code 740: The requested operation requires elevation. [ERROR_ELEVATION_REQUIRED (0x2E4)] | |
| Error Code 741: A reparse should be performed by the Object Manager since the name of the file resulted in a symbolic link. [ERROR_REPARSE (0x2E5)] | |
| Error Code 742: An open/create operation completed while an oplock break is underway. [ERROR_OPLOCK_BREAK_IN_PROGRESS (0x2E6)] | |
| Error Code 743: A new volume has been mounted by a file system. [ERROR_VOLUME_MOUNTED (0x2E7)] | |
| Error Code 744: This success level status indicates that the transaction state already exists for the registry sub-tree [ERROR_RXACT_COMMITTED (0x2E8)] | |
| Error Code 745: This indicates that a notify change request has been completed due to closing the handle which made the notify change request. [ERROR_NOTIFY_CLEANUP (0x2E9)] | |
| Error Code 746: {Connect Failure on Primary Transport} An attempt was made to connect to the remote server %hs on the primary transport [ERROR_PRIMARY_TRANSPORT_CONNECT_FAILED (0x2EA)] | |
| Error Code 747: Page fault was a transition fault. [ERROR_PAGE_FAULT_TRANSITION (0x2EB)] | |
| Error Code 748: Page fault was a demand zero fault. [ERROR_PAGE_FAULT_DEMAND_ZERO (0x2EC)] | |
| Error Code 749: Page fault was a demand zero fault. [ERROR_PAGE_FAULT_COPY_ON_WRITE (0x2ED)] | |
| Error Code 750: Page fault was a demand zero fault. [ERROR_PAGE_FAULT_GUARD_PAGE (0x2EE)] | |
| Error Code 751: Page fault was satisfied by reading from a secondary storage device. [ERROR_PAGE_FAULT_PAGING_FILE (0x2EF)] | |
| Error Code 752: Cached page was locked during operation. [ERROR_CACHE_PAGE_LOCKED (0x2F0)] | |
| Error Code 753: Crash dump exists in paging file. [ERROR_CRASH_DUMP (0x2F1)] | |
| Error Code 754: Specified buffer contains all zeros. [ERROR_BUFFER_ALL_ZEROS (0x2F2)] | |
| Error Code 755: A reparse should be performed by the Object Manager since the name of the file resulted in a symbolic link. [ERROR_REPARSE_OBJECT (0x2F3)] | |
| Error Code 756: The device has succeeded a query-stop and its resource requirements have changed. [ERROR_RESOURCE_REQUIREMENTS_CHANGED (0x2F4)] | |
| Error Code 757: The translator has translated these resources into the global space and no further translations should be performed. [ERROR_TRANSLATION_COMPLETE (0x2F5)] | |
| Error Code 758: A process being terminated has no threads to terminate. [ERROR_NOTHING_TO_TERMINATE (0x2F6)] | |
| Error Code 759: The specified process is not part of a job. [ERROR_PROCESS_NOT_IN_JOB (0x2F7)] | |
| Error Code 760: The specified process is part of a job. [ERROR_PROCESS_IN_JOB (0x2F8)] | |
| Error Code 761: {Volume Shadow Copy Service} The system is now ready for hibernation. [ERROR_VOLSNAP_HIBERNATE_READY (0x2F9)] | |
| Error Code 762: A file system or file system filter driver has successfully completed an FsFilter operation. [ERROR_FSFILTER_OP_COMPLETED_SUCCESSFULLY (0x2FA)] | |
| Error Code 763: The specified interrupt vector was already connected. [ERROR_INTERRUPT_VECTOR_ALREADY_CONNECTED (0x2FB)] | |
| Error Code 764: The specified interrupt vector is still connected. [ERROR_INTERRUPT_STILL_CONNECTED (0x2FC)] | |
| Error Code 765: An operation is blocked waiting for an oplock. [ERROR_WAIT_FOR_OPLOCK (0x2FD)] | |
| Error Code 766: Debugger handled exception [ERROR_DBG_EXCEPTION_HANDLED (0x2FE)] | |
| Error Code 767: Debugger continued [ERROR_DBG_CONTINUE (0x2FF)] | |
| Error Code 768: An exception occurred in a user mode callback and the kernel callback frame should be removed. [ERROR_CALLBACK_POP_STACK (0x300)] | |
| Error Code 769: Compression is disabled for this volume. [ERROR_COMPRESSION_DISABLED (0x301)] | |
| Error Code 770: The data provider cannot fetch backwards through a result set. [ERROR_CANTFETCHBACKWARDS (0x302)] | |
| Error Code 771: The data provider cannot scroll backwards through a result set. [ERROR_CANTSCROLLBACKWARDS (0x303)] | |
| Error Code 772: The data provider requires that previously fetched data is released before asking for more data. [ERROR_ROWSNOTRELEASED (0x304)] | |
| Error Code 773: The data provider was not able to interpret the flags set for a column binding in an accessor. [ERROR_BAD_ACCESSOR_FLAGS (0x305)] | |
| Error Code 774: One or more errors occurred while processing the request. [ERROR_ERRORS_ENCOUNTERED (0x306)] | |
| Error Code 775: The implementation is not capable of performing the request. [ERROR_NOT_CAPABLE (0x307)] | |
| Error Code 776: The client of a component requested an operation which is not valid given the state of the component instance. [ERROR_REQUEST_OUT_OF_SEQUENCE (0x308)] | |
| Error Code 777: A version number could not be parsed. [ERROR_VERSION_PARSE_ERROR (0x309)] | |
| Error Code 778: The iterator's start position is invalid. [ERROR_BADSTARTPOSITION (0x30A)] | |
| Error Code 779: The hardware has reported an uncorrectable memory error. [ERROR_MEMORY_HARDWARE (0x30B)] | |
| Error Code 780: The attempted operation required self healing to be enabled. [ERROR_DISK_REPAIR_DISABLED (0x30C)] | |
| Error Code 781: The Desktop heap encountered an error while allocating session memory. There is more information in the system event log. [ERROR_INSUFFICIENT_RESOURCE_FOR_SPECIFIED_SHARED_SECTION_SIZE (0x30D)] | |
| Error Code 782: The system power state is transitioning from %2 to %3. [ERROR_SYSTEM_POWERSTATE_TRANSITION (0x30E)] | |
| Error Code 783: The system power state is transitioning from %2 to %3 but could enter %4. [ERROR_SYSTEM_POWERSTATE_COMPLEX_TRANSITION (0x30F)] | |
| Error Code 784: A thread is getting dispatched with MCA EXCEPTION because of MCA. [ERROR_MCA_EXCEPTION (0x310)] | |
| Error Code 785: Access to %1 is monitored by policy rule %2. [ERROR_ACCESS_AUDIT_BY_POLICY (0x311)] | |
| Error Code 786: Access to %1 has been restricted by your Administrator by policy rule %2. [ERROR_ACCESS_DISABLED_NO_SAFER_UI_BY_POLICY (0x312)] | |
| Error Code 787: A valid hibernation file has been invalidated and should be abandoned. [ERROR_ABANDON_HIBERFILE (0x313)] | |
| Error Code 788: {Delayed Write Failed} Windows was unable to save all the data for the file %hs; the data has been lost. This error may be caused by network connectivity issues. Please try to save this file elsewhere. [ERROR_LOST_WRITEBEHIND_DATA_NETWORK_DISCONNECTED (0x314)] | |
| Error Code 789: {Delayed Write Failed} Windows was unable to save all the data for the file %hs; the data has been lost. This error was returned by the server on which the file exists. Please try to save this file elsewhere. [ERROR_LOST_WRITEBEHIND_DATA_NETWORK_SERVER_ERROR (0x315)] | |
| Error Code 790: {Delayed Write Failed} Windows was unable to save all the data for the file %hs; the data has been lost. This error may be caused if the device has been removed or the media is write-protected. [ERROR_LOST_WRITEBEHIND_DATA_LOCAL_DISK_ERROR (0x316)] | |
| Error Code 791: The resources required for this device conflict with the MCFG table. [ERROR_BAD_MCFG_TABLE (0x317)] | |
| Error Code 994: Access to the extended attribute was denied. [ERROR_EA_ACCESS_DENIED (0x3E2)] | |
| Error Code 995: The I/O operation has been aborted because of either a thread exit or an application request. [ERROR_OPERATION_ABORTED (0x3E3)] | |
| Error Code 996: Overlapped I/O event is not in a signaled state. [ERROR_IO_INCOMPLETE (0x3E4)] | |
| Error Code 997: Overlapped I/O operation is in progress. [ERROR_IO_PENDING (0x3E5)] | |
| Error Code 998: Invalid access to memory location. [ERROR_NOACCESS (0x3E6)] | |
| Error Code 999: Error performing inpage operation. [ERROR_SWAPERROR (0x3E7)] | |
| Error Code 1001: Recursion too deep; the stack overflowed. [ERROR_STACK_OVERFLOW (0x3E9)] | |
| Error Code 1002: The window cannot act on the sent message. [ERROR_INVALID_MESSAGE (0x3EA)] | |
| Error Code 1003: Cannot complete this function. [ERROR_CAN_NOT_COMPLETE (0x3EB)] | |
| Error Code 1004: Invalid flags. [ERROR_INVALID_FLAGS (0x3EC)] | |
| Error Code 1005: The volume does not contain a recognized file system. Please make sure that all required file system drivers are loaded and that the volume is not corrupted. [ERROR_UNRECOGNIZED_VOLUME (0x3ED)] | |
| Error Code 1006: The volume for a file has been externally altered so that the opened file is no longer valid. [ERROR_FILE_INVALID (0x3EE)] | |
| Error Code 1007: The requested operation cannot be performed in full-screen mode. [ERROR_FULLSCREEN_MODE (0x3EF)] | |
| Error Code 1008: An attempt was made to reference a token that does not exist. [ERROR_NO_TOKEN (0x3F0)] | |
| Error Code 1009: The configuration registry database is corrupt. [ERROR_BADDB (0x3F1)] | |
| Error Code 1010: The configuration registry key is invalid. [ERROR_BADKEY (0x3F2)] | |
| Error Code 1011: The configuration registry key could not be opened. [ERROR_CANTOPEN (0x3F3)] | |
| Error Code 1012: The configuration registry key could not be read. [ERROR_CANTREAD (0x3F4)] | |
| Error Code 1013: The configuration registry key could not be written. [ERROR_CANTWRITE (0x3F5)] | |
| Error Code 1014: One of the files in the registry database had to be recovered by use of a log or alternate copy. The recovery was successful. [ERROR_REGISTRY_RECOVERED (0x3F6)] | |
| Error Code 1015: The registry is corrupted. The structure of one of the files containing registry data is corrupted or the system's memory image of the file is corrupted or the file could not be recovered because the alternate copy or log was absent or corrupted. [ERROR_REGISTRY_CORRUPT (0x3F7)] | |
| Error Code 1016: An I/O operation initiated by the registry failed unrecoverably. The registry could not read in or write out or flush one of the files that contain the system's image of the registry. [ERROR_REGISTRY_IO_FAILED (0x3F8)] | |
| Error Code 1017: The system has attempted to load or restore a file into the registry but the specified file is not in a registry file format. [ERROR_NOT_REGISTRY_FILE (0x3F9)] | |
| Error Code 1018: Illegal operation attempted on a registry key that has been marked for deletion. [ERROR_KEY_DELETED (0x3FA)] | |
| Error Code 1019: System could not allocate the required space in a registry log. [ERROR_NO_LOG_SPACE (0x3FB)] | |
| Error Code 1020: Cannot create a symbolic link in a registry key that already has subkeys or values. [ERROR_KEY_HAS_CHILDREN (0x3FC)] | |
| Error Code 1021: Cannot create a stable subkey under a volatile parent key. [ERROR_CHILD_MUST_BE_VOLATILE (0x3FD)] | |
| Error Code 1022: A notify change request is being completed and the information is not being returned in the caller's buffer. The caller now needs to enumerate the files to find the changes. [ERROR_NOTIFY_ENUM_DIR (0x3FE)] | |
| Error Code 1051: A stop control has been sent to a service that other running services are dependent on. [ERROR_DEPENDENT_SERVICES_RUNNING (0x41B)] | |
| Error Code 1052: The requested control is not valid for this service. [ERROR_INVALID_SERVICE_CONTROL (0x41C)] | |
| Error Code 1053: The service did not respond to the start or control request in a timely fashion. [ERROR_SERVICE_REQUEST_TIMEOUT (0x41D)] | |
| Error Code 1054: A thread could not be created for the service. [ERROR_SERVICE_NO_THREAD (0x41E)] | |
| Error Code 1055: The service database is locked. [ERROR_SERVICE_DATABASE_LOCKED (0x41F)] | |
| Error Code 1056: An instance of the service is already running. [ERROR_SERVICE_ALREADY_RUNNING (0x420)] | |
| Error Code 1057: The account name is invalid or does not exist or the password is invalid for the account name specified. [ERROR_INVALID_SERVICE_ACCOUNT (0x421)] | |
| Error Code 1058: The service cannot be started either because it is disabled or because it has no enabled devices associated with it. [ERROR_SERVICE_DISABLED (0x422)] | |
| Error Code 1059: Circular service dependency was specified. [ERROR_CIRCULAR_DEPENDENCY (0x423)] | |
| Error Code 1060: The specified service does not exist as an installed service. [ERROR_SERVICE_DOES_NOT_EXIST (0x424)] | |
| Error Code 1061: The service cannot accept control messages at this time. [ERROR_SERVICE_CANNOT_ACCEPT_CTRL (0x425)] | |
| Error Code 1062: The service has not been started. [ERROR_SERVICE_NOT_ACTIVE (0x426)] | |
| Error Code 1063: The service process could not connect to the service controller. [ERROR_FAILED_SERVICE_CONTROLLER_CONNECT (0x427)] | |
| Error Code 1064: An exception occurred in the service when handling the control request. [ERROR_EXCEPTION_IN_SERVICE (0x428)] | |
| Error Code 1065: The database specified does not exist. [ERROR_DATABASE_DOES_NOT_EXIST (0x429)] | |
| Error Code 1066: The service has returned a service-specific error code. [ERROR_SERVICE_SPECIFIC_ERROR (0x42A)] | |
| Error Code 1067: The process terminated unexpectedly. [ERROR_PROCESS_ABORTED (0x42B)] | |
| Error Code 1068: The dependency service or group failed to start. [ERROR_SERVICE_DEPENDENCY_FAIL (0x42C)] | |
| Error Code 1069: The service did not start due to a logon failure. [ERROR_SERVICE_LOGON_FAILED (0x42D)] | |
| Error Code 1070: After starting the service hung in a start-pending state. [ERROR_SERVICE_START_HANG (0x42E)] | |
| Error Code 1071: The specified service database lock is invalid. [ERROR_INVALID_SERVICE_LOCK (0x42F)] | |
| Error Code 1072: The specified service has been marked for deletion. [ERROR_SERVICE_MARKED_FOR_DELETE (0x430)] | |
| Error Code 1073: The specified service already exists. [ERROR_SERVICE_EXISTS (0x431)] | |
| Error Code 1074: The system is currently running with the last-known-good configuration. [ERROR_ALREADY_RUNNING_LKG (0x432)] | |
| Error Code 1075: The dependency service does not exist or has been marked for deletion. [ERROR_SERVICE_DEPENDENCY_DELETED (0x433)] | |
| Error Code 1076: The current boot has already been accepted for use as the last-known-good control set. [ERROR_BOOT_ALREADY_ACCEPTED (0x434)] | |
| Error Code 1077: No attempts to start the service have been made since the last boot. [ERROR_SERVICE_NEVER_STARTED (0x435)] | |
| Error Code 1078: The name is already in use as either a service name or a service display name. [ERROR_DUPLICATE_SERVICE_NAME (0x436)] | |
| Error Code 1079: The account specified for this service is different from the account specified for other services running in the same process. [ERROR_DIFFERENT_SERVICE_ACCOUNT (0x437)] | |
| Error Code 1080: Failure actions can only be set for Win32 services not for drivers. [ERROR_CANNOT_DETECT_DRIVER_FAILURE (0x438)] | |
| Error Code 1081: This service runs in the same process as the service control manager. Therefore the service control manager cannot take action if this service's process terminates unexpectedly. [ERROR_CANNOT_DETECT_PROCESS_ABORT (0x439)] | |
| Error Code 1082: No recovery program has been configured for this service. [ERROR_NO_RECOVERY_PROGRAM (0x43A)] | |
| Error Code 1083: The executable program that this service is configured to run in does not implement the service. [ERROR_SERVICE_NOT_IN_EXE (0x43B)] | |
| Error Code 1084: This service cannot be started in Safe Mode [ERROR_NOT_SAFEBOOT_SERVICE (0x43C)] | |
| Error Code 1100: The physical end of the tape has been reached. [ERROR_END_OF_MEDIA (0x44C)] | |
| Error Code 1101: A tape access reached a filemark. [ERROR_FILEMARK_DETECTED (0x44D)] | |
| Error Code 1102: The beginning of the tape or a partition was encountered. [ERROR_BEGINNING_OF_MEDIA (0x44E)] | |
| Error Code 1103: A tape access reached the end of a set of files. [ERROR_SETMARK_DETECTED (0x44F)] | |
| Error Code 1104: No more data is on the tape. [ERROR_NO_DATA_DETECTED (0x450)] | |
| Error Code 1105: Tape could not be partitioned. [ERROR_PARTITION_FAILURE (0x451)] | |
| Error Code 1106: When accessing a new tape of a multivolume partition the current block size is incorrect. [ERROR_INVALID_BLOCK_LENGTH (0x452)] | |
| Error Code 1107: Tape partition information could not be found when loading a tape. [ERROR_DEVICE_NOT_PARTITIONED (0x453)] | |
| Error Code 1108: Unable to lock the media eject mechanism. [ERROR_UNABLE_TO_LOCK_MEDIA (0x454)] | |
| Error Code 1109: Unable to unload the media. [ERROR_UNABLE_TO_UNLOAD_MEDIA (0x455)] | |
| Error Code 1110: The media in the drive may have changed. [ERROR_MEDIA_CHANGED (0x456)] | |
| Error Code 1111: The I/O bus was reset. [ERROR_BUS_RESET (0x457)] | |
| Error Code 1112: No media in drive. [ERROR_NO_MEDIA_IN_DRIVE (0x458)] | |
| Error Code 1113: No mapping for the Unicode character exists in the target multi-byte code page. [ERROR_NO_UNICODE_TRANSLATION (0x459)] | |
| Error Code 1114: A dynamic link library (DLL) initialization routine failed. [ERROR_DLL_INIT_FAILED (0x45A)] | |
| Error Code 1115: A system shutdown is in progress. [ERROR_SHUTDOWN_IN_PROGRESS (0x45B)] | |
| Error Code 1116: Unable to abort the system shutdown because no shutdown was in progress. [ERROR_NO_SHUTDOWN_IN_PROGRESS (0x45C)] | |
| Error Code 1117: The request could not be performed because of an I/O device error. [ERROR_IO_DEVICE (0x45D)] | |
| Error Code 1118: No serial device was successfully initialized. The serial driver will unload. [ERROR_SERIAL_NO_DEVICE (0x45E)] | |
| 1 - 1118 | 1119 - 1935 | 1936 - 8250 | 8251 - 12008 | 12009 - 15841 | |
Hii guys, My name is Ganeshkumar and I’m a Computer Hardware Engineer and I proudly love to teach about computer software and hardware repairing stuffs. My hobby is blogging about computer problems solutions
ConversionConversion EmoticonEmoticon